difference between bottom brackets for road and track?

Bryan K. Walton said:

I picked up an early 70s Gitane track frame at a bike swap this past weekend. The bottom bracket
shell is French threaded. I know that I could probably run a tap through it to English thread it,
but I would rather not if I can help it. So . . .

So I started looking on the web for french threaded bottom brackets. Sheldon Brown has some pretty
nice Stronglights:

sheldonbrown.comfrench cranks.htmlOpen ↗

But I am unsure whether I need to be looking for distinctly track bottom brackets, or if road vs.
track doesn't matter in this area.

Any pointers?

As only one chainring is used on a track bike, the spindle length is pretty short to get the correct
chainline. Track BBs may be less well sealed, on the assumption that they won't be used on wet
roads. A lot of cheaper track hubs wouldn't last long on a commute because water can run straight
into the bearings.

Apart from that, they all do the same job.

On 26 Jan 2004 14:02:04 CST, "Bryan K. Walton" <[email hidden]>

Quoted message said:

I picked up an early 70s Gitane track frame at a bike swap this past weekend. The bottom bracket
shell is French threaded. I know that I could probably run a tap through it to English thread it,
but I would rather not if I can help it. So . . .

So I started looking on the web for french threaded bottom brackets. Sheldon Brown has some pretty
nice Stronglights:

sheldonbrown.comfrench cranks.htmlOpen ↗

But I am unsure whether I need to be looking for distinctly track bottom brackets, or if road vs.
track doesn't matter in this area.

Any pointers?

Thanks, Bryan

Most track cranks use a 110mm axle, make sure you get the right taper (ISO vs. JIS) for your cranks.
Using a road BB on a track bike is OK, unless you're planning to be a pro kieren rider in japan
where you'll need a NJS certified BB!

Kinky Cowboy*

*Batteries not included May contain traces of nuts Your milage may vary

Bryan K. Walton said:

I picked up an early 70s Gitane track frame at a bike swap this past weekend. The bottom bracket
shell is French threaded. I know that I could probably run a tap through it to English thread it,
but I would rather not if I can help it. So . . .

So I started looking on the web for french threaded bottom brackets. Sheldon Brown has some pretty
nice Stronglights:

sheldonbrown.comfrench cranks.htmlOpen ↗

But I am unsure whether I need to be looking for distinctly track bottom brackets, or if road vs.
track doesn't matter in this area.

Any pointers?

Cup thread matches frame; Spindle length matches crank.

Oh, and a BSC tap at 1.370"=34.85mm will not do much in your 35mm threads

--
Andrew Muzi www.yellowjersey.org Open every day since 1 April, 1971

In article said:

As only one chainring is used on a track bike, the spindle length is pretty short to get the
correct chainline. Track BBs may be less well

Thanks for the reply, are you saying that the spindle length for the Stronglights I referred to are
too short to get the correct chainline? What spindle length do I need for a French track frame?

Thanks, Bryan Walton

--
************** remove the "REMOVE" from my email to email **************

In article <[email hidden]>,

Kinky Cowboy said:

Most track cranks use a 110mm axle, make sure you get the right taper (ISO vs. JIS) for your
cranks. Using a road BB on a track bike is OK, unless you're planning to be a pro kieren rider in
japan where you'll need a NJS certified BB!

Forgive me, when you refer to a 110mm axle, are you referring to spindle dimensions? Ore
something else?

Thanks, Bryan Walton

--
************** remove the "REMOVE" from my email to email **************

In article said:

Cup thread matches frame; Spindle length matches crank.

Oh, and a BSC tap at 1.370"=34.85mm will not do much in your 35mm threads

Hi Andrew, for clarification, are you saying that I should not bother with running the tap?

Thanks, Bryan

--
************** remove the "REMOVE" from my email to email **************

Bryan K. Walton said:

...are you saying that the spindle length for the Stronglights I referred to are too short to get
the correct chainline?

Too long, not too short.

Quoted message said:

What spindle length do I need for a French track frame?

That Stronglight bb is 124 mm with a 4 mm offset to the right.

While it will fit any French threaded _frame_, the spindle length depends on the crankset and the
desired chainline.

Most track specific cranks are looking for something like a 109 mm symmetrical spindle, so if you
were to buy one of those Stronglights from me, nice as it is, the chainring would probably be 9 or
10 mm too far to the right.

See: sheldonbrown.comchainlineOpen ↗

I do have loose ball bbs that would work for you, which spindle would, again, depend on the crank
you plan to use.

Another option is Phil Wood. They're expensive but they are really good, and they make something to
fit everything.

Sheldon "Chainline" Brown +-----------------------------------------+
| A ship in the harbor is safe, but | that is not what ships are built for. | --John A. Shedd |
+-----------------------------------------+ Harris Cyclery, West Newton, Massachusetts Phone 617-244-
9772 FAX 617-244-1041 harriscyclery.comharriscyclery.comOpen ↗ Hard-to-find parts shipped Worldwide
captainbike.comcaptainbike.comOpen ↗ sheldonbrown.comsheldonbrown.comOpen ↗

Quoted message said:

In article said:

As only one chainring is used on a track bike, the spindle length is pretty short to get the
correct chainline. Track BBs may be less well

Bryan K. Walton said:

Thanks for the reply, are you saying that the spindle length for the Stronglights I referred
to are too short to get the correct chainline? What spindle length do I need for a French
track frame?

Cup thread matches frame. Spindle matches crank.

--
Andrew Muzi www.yellowjersey.org Open every day since 1 April, 1971

Quoted message said:

In article said:

Cup thread matches frame; Spindle length matches crank. Oh, and a BSC tap at 1.370"=34.85mm will
not do much in your 35mm threads

Bryan K. Walton said:

Hi Andrew, for clarification, are you saying that I should not bother with running the tap?

What's the goal?

If you want to clear any paint and brazing excess from your frame threads then an m35xP1 metric tap
would be just the thing.

You that you wanted to make the 35mm hole smaller using a
34.85mm tap, and that's physically impossible!

--
Andrew Muzi www.yellowjersey.org Open every day since 1 April, 1971

In article said:

Most track specific cranks are looking for something like a 109 mm symmetrical spindle, so if you
were to buy one of those Stronglights from me, nice as it is, the chainring would probably be 9 or
10 mm too far to the right.

I do have loose ball bbs that would work for you, which spindle would, again, depend on the crank
you plan to use.

Hi Sheldon, thanks for the reply. I took a another look at your website, and based on what you say
above, it seems that I could put together a combination of a T.A. right and left cup, and lock ring;
along with a T.A. track bottom bracket and be able to leave the bottom bracket french threaded? Is
that correct?

Thanks, Bryan

--
************** remove the "REMOVE" from my email to email **************

On 26 Jan 2004 14:02:04 CST "Bryan K. Walton" <[email hidden]>

Quoted message said:

I picked up an early 70s Gitane track frame at a bike swap this past weekend. The bottom bracket
shell is French threaded. I know that I could probably run a tap through it to English thread it,
but I would rather not if I can help it. So . . .

As Andy has tried to explain, the English tap is slightly SMALLER than the existing French thread,
so this approach has no chance of working.

-
-----------------------------------------------
Jim Adney [email hidden] Madison, WI 53711 USA
-----------------------------------------------

"Bryan K. Walton" <[email hidden]> wrote in message news:<[email hidden]>...

Quoted message said:

In article said:

Most track cranks use a 110mm axle, make sure you get the right taper (ISO vs. JIS) for your
cranks. Using a road BB on a track bike is OK, unless you're planning to be a pro kieren rider
in japan where you'll need a NJS certified BB!

Forgive me, when you refer to a 110mm axle, are you referring to spindle dimensions? Ore
something else?

Thanks, Bryan Walton

110-mm is the overall width of the spindle. chk businesscycles.com for spindle info/stuff. every
track spindle i have, about 5-6, is "narrow"/Campy taper. i've had good success w/ mixing &
matching spindles & cups. i have a couple sets of Sugino french cups i got off of eBay. also, are
you sure it's French? (just checking. my 70s Gitane track turned out to be english after i bought
a french HS for it. i just assume it was french.) the nice thing about the Phil option is you can
sell the frame & transfer the BB to the new frame by getting new rings.

In article said:

What's the goal?

If you want to clear any paint and brazing excess from your frame threads then an m35xP1 metric
tap would be just the thing.

You that you wanted to make the 35mm hole smaller using a
34.85mm tap, and that's physically impossible!

Thanks, I understand now. If I want to change the thread, I need to go Italian.

Cheers, Bryan

--
************** remove the "REMOVE" from my email to email **************