Crank creak, grease bottom bracket spindle

Quoted message said:

I'm getting a creak from my left crank arm, tried tightening the bolt
without much luck (it stopped for 2 minutes). I pulled the crank arm
planning to clean it up and grease the bolt prior to retightening.
It's been so long that I can't recall: anything I shouldn't grease,
like the BB spindle?

It's a generic cartridge BB in a circa 1988 Bridgestone MB-3 frame. I
don't have the splined tool to remove the BB (unless it's the same as a
splined cassette wrench), so if this doesn't work, I may take it to the
shop.
mx

Shimano say never to grease the taper of the spindle, TA say always to
grease it (I don't know what the Campag view is). Make of this what you
will - I've greased mine with anti-seize since I had a crank seize
firmly onto a spindle.

Shimano Octalink spindles are always greased.

Zog The Undeniable said:

Shimano say never to grease the taper of the spindle, TA say always to
grease it (I don't know what the Campag view is).

Sgrassare e pulire accuratamente il quadro del perno ed il foro quadro
delle pedivelle per garantire uno stabile accoppiamento

😉
--
---
Marten Gerritsen

INFOapestaartjeM-GINEERINGpuntNL
www.m-gineering.nl

Quoted message said:

I'm getting a creak from my left crank arm, tried tightening the bolt
without much luck (it stopped for 2 minutes). I pulled the crank arm
planning to clean it up and grease the bolt prior to retightening.
It's been so long that I can't recall: anything I shouldn't grease,
like the BB spindle?

It's a generic cartridge BB in a circa 1988 Bridgestone MB-3 frame. I
don't have the splined tool to remove the BB (unless it's the same as a
splined cassette wrench), so if this doesn't work, I may take it to the
shop.
mx

Most likely is the cups in the BB are making the noise. Few shops
realize you can take the right cup off early shimano cart BBs. Do this,
grease insdie both cups, inside the BB shell and tighten, tight. I
personally don't grease crank spindles on square taper, never have for
over 20 years, have never had a crank fall off, have never seen that
grease on to a spindle eliminates any otherwise unsolvable BB creaks.
Torque to about 30 ft-lbs.

"M-gineering" <[email hidden]> wrote in message
news:[email hidden]...

Quoted message said:

Zog The Undeniable said:

Shimano say never to grease the taper of the spindle, TA say always to
grease it (I don't know what the Campag view is).

Sgrassare e pulire accuratamente il quadro del perno ed il foro quadro
delle pedivelle per garantire uno stabile accoppiamento

😉
--
---
Marten Gerritsen

INFOapestaartjeM-GINEERINGpuntNL
www.m-gineering.nl\\

sa;liafhopiw qoirhc poiwuery mope8y cnp91whuc as';loru b [sapoif'
qwpoidj p[oy aspoih

Quoted message said:

I'm getting a creak from my left crank arm, tried tightening the bolt
without much luck (it stopped for 2 minutes). I pulled the crank arm
planning to clean it up and grease the bolt prior to retightening.
It's been so long that I can't recall: anything I shouldn't grease,
like the BB spindle?

It's a generic cartridge BB in a circa 1988 Bridgestone MB-3 frame. I
don't have the splined tool to remove the BB (unless it's the same as a
splined cassette wrench), so if this doesn't work, I may take it to the
shop.
mx

In addition to the other advice you've received, check the chain ring
bolts.

M-gineering said:

Zog The Undeniable said:

Shimano say never to grease the taper of the spindle, TA say always to
grease it (I don't know what the Campag view is).

Sgrassare e pulire accuratamente il quadro del perno ed il foro quadro
delle pedivelle per garantire uno stabile accoppiamento

😉

Dear Don Corleone,

Roughly, a caption that exhorts us to degrease and clean up
the crank to guarantee a stable connection.

S'io credesse che mia risposta fosse
A persona che mai tornasse al mondo,
Questa fiamma staria senza piu scosse.
Ma perciocche giammai di questo fondo
Non torno vivo alcun, s'i'odo il vero,
Senza tema d'infamia ti rispondo.

Guido

Someone said:

I'm getting a creak from my left crank arm, tried tightening the
bolt without much luck (it stopped for 2 minutes). I pulled the
crank arm planning to clean it up and grease the bolt prior to
retightening. It's been so long that I can't recall: anything I
shouldn't grease, like the BB spindle?

Quoted message said:

It's a generic cartridge BB in a circa 1988 Bridgestone MB-3 frame.
I don't have the splined tool to remove the BB (unless it's the same
as a splined cassette wrench), so if this doesn't work, I may take
it to the shop.

Most such mysterious creaking sounds that show no relation to crank
attachment, as you describe, are made by the shoe-pedal interface. To
rule that out, put some grease or oil on the sole of the shoe where it
contacts the pedal. That gets rid of a lot of speculation.

Jobst Brandt

[email hidden] ha scritto:

Quoted message said:

M-gineering said:

Zog The Undeniable said:

Shimano say never to grease the taper of the spindle, TA say always to
grease it (I don't know what the Campag view is).

Sgrassare e pulire accuratamente il quadro del perno ed il foro quadro
delle pedivelle per garantire uno stabile accoppiamento

😉

Dear Don Corleone,

Roughly, a caption that exhorts us to degrease and clean up
the crank to guarantee a stable connection.

S'io credesse che mia risposta fosse
A persona che mai tornasse al mondo,
Questa fiamma staria senza piu scosse.
Ma perciocche giammai di questo fondo
Non torno vivo alcun, s'i'odo il vero,
Senza tema d'infamia ti rispondo.

Guido

But... ROTFL!!! Altho I doubt there are many people here that can read
a 700ish-yr old "Italian" poem. It would be hard for an Italian as well
(I had to read twice to understand).
Ciao
Luca

jobst.brandt said:

Someone said:

I'm getting a creak from my left crank arm, tried tightening the
bolt without much luck (it stopped for 2 minutes). I pulled the
crank arm planning to clean it up and grease the bolt prior to
retightening. It's been so long that I can't recall: anything I
shouldn't grease, like the BB spindle?

Quoted message said:

It's a generic cartridge BB in a circa 1988 Bridgestone MB-3 frame.
I don't have the splined tool to remove the BB (unless it's the same
as a splined cassette wrench), so if this doesn't work, I may take
it to the shop.

Most such mysterious creaking sounds that show no relation to crank
attachment, as you describe, are made by the shoe-pedal interface. To
rule that out, put some grease or oil on the sole of the shoe where it
contacts the pedal. That gets rid of a lot of speculation.

Saddle rails are another common source of such creaks. All of these
creaks can resonate through the frame tubes, so they sound like
they're from the frame/BB.

Matt O.

Luca Magnoni said:

[email hidden] ha scritto:

Quoted message said:

M-gineering said:

Zog The Undeniable wrote:

> Shimano say never to grease the taper of the spindle, TA say always to
> grease it (I don't know what the Campag view is).

Sgrassare e pulire accuratamente il quadro del perno ed il foro quadro
delle pedivelle per garantire uno stabile accoppiamento

😉

Dear Don Corleone,

Roughly, a caption that exhorts us to degrease and clean up
the crank to guarantee a stable connection.

S'io credesse che mia risposta fosse
A persona che mai tornasse al mondo,
Questa fiamma staria senza piu scosse.
Ma perciocche giammai di questo fondo
Non torno vivo alcun, s'i'odo il vero,
Senza tema d'infamia ti rispondo.

Guido

But... ROTFL!!! Altho I doubt there are many people here that can read
a 700ish-yr old "Italian" poem. It would be hard for an Italian as well
(I had to read twice to understand).
Ciao
Luca

Dear Luca,

Well, the passage is more familiar on an English newsgroup
than an Italian might expect.

Its real claim to fame in the barbarian world (where rhymes
are difficult) is that Eliot used it even more appropriately
as his epigraph for Prufrock.

And it did seem appropriate for a reply--few escape after
descending into RBT, where . . .

Io venni in loco d'ogne luce muto,
che mugghia come fa mar per tempesta,
se da contrari venti è combattuto.

La bufera infernal, che mai non resta,
mena li spirti con la sua rapina;
voltando e percotendo li molesta.

Quando giungon davanti a la ruina,
quivi le strida, il compianto, il lamento;
bestemmian quivi la virtù divina.

I came to a place where light was absent,
A place which bellowed like a stormy sea when
Clashing winds whip it into torment.

The infernal hurricane, which can never slacken,
Drives the spirits with its violence;
Whirling and lashing, it leaves them beaten.

Swept back before their place of sentence,
The spirits shriek, moan, lament, and
Curse the divine power with vehemence.

The curious may discover further descriptions of the
newsgroup in both English and Italian at sites like this:

http://home.earthlink.net/~zimls/HELLV.html#28

Click on the "inferno v" links at the side to toggle back
and forth.

Cheers,

Carl Fogel