Spoke nipple unscrewed.

Quoted post said:

Originally posted by Ed
For the first time in my experience a spoke nipple unscrewed
itself. What was the cause and what can I do to prevent it
from happening again?

This was on a radially laced wheel.

Cause is spoke going loose.
Rider weight, spoking pattern, wear of the spoke hole, vibration all contribute.

You can build a wheel with new spokes and new hub with 3 cross lacing, proper tension, spoke alignment, and stress relieving.

If you want to use the same hub again I suggest using spoke head washers, the same radial pattern, and even high tension.
I never suggest radial spoking, but once the hub has been laced that way it should continue ...to minimize the chances of breaking the flange.

Quoted post said:

Originally posted by daveornee
Cause is spoke going loose.
Rider weight, spoking pattern, wear of the spoke hole, vibration all contribute.

You can build a wheel with new spokes and new hub with 3 cross lacing, proper tension, spoke alignment, and stress relieving.

If you want to use the same hub again I suggest using spoke head washers, the same radial pattern, and even high tension.
I never suggest radial spoking, but once the hub has been laced that way it should continue ...to minimize the chances of breaking the flange.

If this is a new wheel it could also be that you didn't get a good match between the nipple and spoke threads. I've seen shops get a little sloppy about where they put back the extras so you might have a 14g nipple on a 15g spoke. That would probably come off (not unscrew) pretty quickly... unlikely to be the cause if this wheel has seen a lot of use.

Quoted message said:

If this is a new wheel it could also be that you didn't
get a good match between the nipple and spoke threads.
I've seen shops get a little sloppy about where they put
back the extras so you might have a 14g nipple on a 15g
spoke. That would probably come off (not unscrew) pretty
quickly... unlikely to be the cause if this wheel has seen
a lot of use.

14g nips on 15g spokes get proper tension, then go PING as
the nip flies off, in my experience.

--
Phil, Squid-in-Training

Ed said:

For the first time in my experience a spoke nipple
unscrewed itself. What was the cause and what can I do to
prevent it from happening again?

This was on a radially laced wheel.

Radial spokes have a higher tendency to unscrew, as you've
found. A bit of Loctite will stop it, as will higher spoke
tension (only if the wheel is a bit slack already).

ed-<< For the first time in my experience a spoke nipple
unscrewed itself. What was the cause and what can I do to
prevent it from happening again?

This was on a radially laced wheel. >><BR><BR>

Either the tension of the entire wheel was too low of ya
wacked the rim, pushed a section in, via a dent, and the
tension at that place was too low...

Peter Chisholm Vecchio's Bicicletteria 1833 Pearl St.
Boulder, CO, 80302
(303)440-3535 vecchios.comvecchios.comOpen ↗ "Ruote convenzionali
costruite eccezionalmente bene"

On 22 May 2004 12:46:41 GMT, [email hidden] (Qui si parla

Campagnolo ) may have said:

ed-<< For the first time in my experience a spoke nipple
unscrewed itself. What was the cause and what can I do to
prevent it from happening again?

This was on a radially laced wheel. >><BR><BR>

Either the tension of the entire wheel was too low of ya
wacked the rim, pushed a section in, via a dent, and the
tension at that place was too low...

Or maybe a cracked Mavic?

--
My email address is antispammed; pull WEEDS if replying via
e-mail. Typoes are not a bug, they're a feature. Words
processed in a facility that contains nuts.

In article <[email hidden]>,
[email hidden] says...

Quoted message said:

For the first time in my experience a spoke nipple
unscrewed itself. What

was

Quoted message said:

the cause and what can I do to prevent it from happening
again? This was on a radially laced wheel.

That is usually a sign of a spoke that was not tight enough.
--------------
Alex

Someone said:

Quoted message said:

For the first time in my experience a spoke nipple
unscrewed itself. What was the cause and what can I do to
prevent it from happening again? This was on a radially
laced wheel.

Alex Rodriguez said:

That is usually a sign of a spoke that was not tight
enough.

Not necessarily, when a radially spoked wheel is involved.
Radially spoked wheels tend to be prone to this unless
tension is very high, likely for two reasons:

1. The spokes aren't interlaced, since they don't cross, so
there's no crossing spoke to take up the slack when the
wheel load loosens the bottom spoke.

B. The nipples come straight out of the rim holes, without
the usual sideward bend they get on a typical semi-
tangent wheel. This makes the nipples easier to turn.

I generally build radial wheels with dry spokes, and
sometimes resort to a wicking threadlocker.

Sheldon "Better Living Through Chemistry" Brown +--------------------------------------------
+
| In order to understand recursion, | first, you have to
| understand recursion. |
+--------------------------------------------+ Harris
Cyclery, West Newton, Massachusetts Phone 617-244-9772 FAX
617-244-1041 harriscyclery.comharriscyclery.comOpen ↗ Hard-to-find parts
shipped Worldwide captainbike.comcaptainbike.comOpen ↗
sheldonbrown.comsheldonbrown.comOpen ↗