Spoke count and gauge for open pro wheelset?

Zaf said:

OK its time to get new wheels. Having read quite a few posts on wheels, I'm going to go
Ultegra/Open Pro. So the only decision to make is spoke count and gauge. I'm a 190# rec rider the
roads here in the northeast are pretty much destroyed from the severe winter, lets hope I can
avoid these craters. I have no problem going to 36 in the rear. I find

Quoted message said:

15/16/16 spokes, would these be sufficient (36R, 32F)?

I don't know why they would not beef up the other end (which end?) to 15 again, but other than that
they are OK. I tend to use 14/15, but there is an argument for 15/16. Especially with 36 in the
rear, you should be OK.

As far as potholes go, don't run into them. It's not so much your spokes, as your tires, that will
go first. That and your teeth if you hit a really deep one. I prefer to avoid them.

Quoted message said:

Also, any down side if I yield again to vanity and go with a color anodized rim?

Yeah, there is, but it's hard to avoid them. The hard anodizing makes the metal more brittle, more
likely to crack. Cracks are bad. I really prefer plain polished rims, but they are hard to find.

--

David L. Johnson

__o | The trouble with the rat race is that even if you win you're _`\(,_ | still a rat. --Lilly
Tomlin (_)/ (_) |

"Zaf" <[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

OK its time to get new wheels. Having read quite a few posts on wheels, I'm going to go
Ultegra/Open Pro. So the only decision to make is spoke count and gauge. I'm a 190# rec rider the
roads here in the northeast are pretty much destroyed from the severe winter, lets hope I can
avoid these craters. I have no problem going to 36 in

Quoted message said:

offers them with 15/16/16 spokes, would these be sufficient (36R,
32F)? Also, any down side if I yield again to vanity and go with a color anodized rim?

If you are going to ride 36, I think that the 15/16's will be OK. For the 32 hole front, I'd ride
14/15's. Anything thinner in the front and you may run into problems (unless you go 36 there too).

Mike

In article said:

OK its time to get new wheels. Having read quite a few posts on wheels, I'm going to go
Ultegra/Open Pro. So the only decision to make is spoke count and gauge. I'm a 190# rec rider the
roads here in the northeast are pretty much destroyed from the severe winter, lets hope I can avoid
these craters. I have no problem going to 36 in

Quoted message said:

offers them with 15/16/16 spokes, would these be sufficient (36R,
32F)?

I think that will do fine if you use the right tires, but I see no reason to not do 36 in front as
well if top reliability is the goal.

Quoted message said:

Also, any down side if I yield again to vanity and go with a color anodized rim?

Might not last as well as silver. I have not personally had problems with cracking the current Mavic
offerings when anodized, but in general I avoid anodizing when I have the option. Anodizing also
often fades unevenly and may cause more aesthetic annoyance than benefit.

Use brass nipples so you can get more spoke tension, the wheels will be stronger.

--Paul

Mike S.' mikeshaw2@coxDOTnet said:

For the 32 hole front, I'd ride 14/15's. Anything thinner in the front and you may run into
problems (unless you go 36 there too).

I"ve run straight 15 ga x 32 spokes forever and I weigh 200 lbs. I even use them in 28 hole rims.
I've had no problems. What problem would you expect?

(Zaf) said:

OK its time to get new wheels. Having read quite a few posts on wheels, I'm going to go
Ultegra/Open Pro. So the only decision to make is spoke count and gauge. I'm a 190# rec rider the
roads here in the northeast are pretty much destroyed from the severe winter, lets hope I can avoid
these craters. I have no problem going to 36 in the rear.

A 32 spoke front wheel will be at least as strong as a 36 spoke rear wheel, so there's no reason not
to do this.

Quoted message said:

offers them with 15/16/16 spokes, would these be sufficient (36R,
32F)?

I suspect you mean 15/16/15g. Yes, I think they'd be sufficient (I've run the same size spokes for
years on my MTB wheels without problems).

Quoted message said:

Also, any down side if I yield again to vanity and go with a color anodized rim?

Yep. The anodizing embrittles the surface of the rim, and the microscopic fractures that inevitably
occur can propogate to the underlying metal in the rim (translated: your spokes may pull through).

Also, follow the advice you got about using brass nipples.

Mark Hickey Habanero Cycles habcycles.comhabcycles.comOpen ↗ Home of the $695 ti frame

Mark Hickey said:

Quoted message said:

OK its time to get new wheels. Having read quite a few posts on wheels, I'm going to go
Ultegra/Open Pro. So the only decision to make is spoke count and gauge. I'm a 190# rec rider the
roads here in the northeast are pretty much destroyed from the severe winter, lets hope I can
avoid these craters. I have no problem going to 36 in the rear.

Quoted message said:

A 32 spoke front wheel will be at least as strong as a 36 spoke rear wheel, so there's no reason
not to do this.

I don't know on what basis you make that assessment but it depends on the use. When I descend I
brake hard, hard enough to at times raise the rear wheel. Therefore, practically my full weight is
on the front. If you are concerned about catastrophic failure or slackening spokes, 36 front and
rear are a good measure. On the other hand, we have seen that 16 front and rear can handle the job
under more ideal conditions. There are 14 spoke wheels as well.

Quoted message said:

Quoted message said:

offers them with 15/16/16 spokes, would these be sufficient (36R,
32F)?

Quoted message said:

I suspect you mean 15/16/15g. Yes, I think they'd be sufficient (I've run the same size spokes for
years on my MTB wheels without problems).

That's what I have been using since historic times with good success.

Jobst Brandt [email hidden] Palo Alto CA

"Zaf" <[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

OK its time to get new wheels. Having read quite a few posts on wheels, I'm going to go
Ultegra/Open Pro. So the only decision to make is spoke count and gauge. I'm a 190# rec rider the
roads here in the northeast are pretty much destroyed from the severe winter, lets hope I can
avoid these craters. I have no problem going to 36 in

Quoted message said:

offers them with 15/16/16 spokes, would these be sufficient (36R,
32F)? Also, any down side if I yield again to vanity and go with a color anodized rim?

Listen to Jobst. Use the thinnest butted spokes which your builder can crank up to max tension
without spoke twist in the final product. That seems to be 15/16 for most builders on modern hubs.
Apparently 14/17's are difficult in thes regard.

Robin Hubert

zafdor-<< Having read quite a few posts on wheels, I'm going to go Ultegra/Open Pro.

<< So the only decision to make is spoke count and gauge. I'm a 190# rec rider the roads here in the
northeast are pretty much destroyed from the severe winter.

offers them with 15/16/16 spokes, would these be sufficient (36R,
32F)?

Not a good idea IMO-36 rear, 32 front, 14/15/brass/3 cross built well..

<< Also, any down side if I yield again to vanity and go with a color anodized rim?

Colored(black for instance) is nbot really 'hard anodized' just colored.

Peter Chisholm Vecchio's Bicicletteria 1833 Pearl St. Boulder, CO, 80302
(33)440-3535 vecchios.comvecchios.comOpen ↗ "Ruote convenzionali costruite eccezionalmente bene"

Zaf said:

OK its time to get new wheels. Having read quite a few posts on wheels, I'm going to go
Ultegra/Open Pro. So the only decision to make is spoke count and gauge. I'm a 190# rec rider the
roads here in the northeast are pretty much destroyed from the severe winter, lets hope I can
avoid these craters. I have no problem going to 36 in

Quoted message said:

offers them with 15/16/16 spokes, would these be sufficient (36R,
32F)? Also, any down side if I yield again to vanity and go with a color anodized rim?

I'm about the same weight as you. 15-16-15 all around is OK. I prefer either 14-15-14 or straight 15
ga on the rear drive side.

Have you read about the problems folks have had with "clicking" Open Pros?

Art Harris

Quoted message said:

Mark Hickey writes:

Quoted message said:

Quoted message said:

A 32 spoke front wheel will be at least as strong as a 36 spoke rear wheel, so there's no reason
not to do this.

I don't know on what basis you make that assessment but it depends on the use. When I descend I
brake hard, hard enough to at times raise the rear wheel. Therefore, practically my full weight is
on the front. If you are concerned about catastrophic failure or slackening spokes, 36 front and
rear are a good measure. On the other hand, we have seen that 16 front and rear can handle the job
under more ideal conditions. There are 14 spoke wheels as well.

I seldom worry about overloading my wheels when braking or when accelerating. The point I was making
was that due to relative weight distribution on the bike and the limitation on bracing angle on the
rear wheel's right (drive side) spokes, the same number of spokes aren't necessary on the front
wheel to provide the same (though not necessarily greater...) margin. That's not to say there's
anything wrong with using four more spokes, of course.

I could be wrong, but I seem to remember you saying much the same thing in days gone by...

Mark Hickey Habanero Cycles habcycles.comhabcycles.comOpen ↗ Home of the $695 ti frame

(Zaf) said:

Quoted message said:

Mark Hickey writes:

Quoted message said:

Quoted message said:

Quoted message said:

I suspect you mean 15/16/15g. Yes, I think they'd be sufficient (I've run the same size spokes
for years on my MTB wheels without problems).

Quoted message said:

Ooops, yes, I ment 15/16/15. I will be going with 36 in the front also, I think will only mean
another 50gm or so.

It won't be that much. You're probably going to add ~22 grams, minus the material that's been
drilled out of the extra four holes in the rim and hub (hey, as long as we're weighing "nits"😉. ;-)

Mark Hickey Habanero Cycles habcycles.comhabcycles.comOpen ↗ Home of the $695 ti frame

Zaf Dor? said:

Quoted message said:

I don't know on what basis you make that assessment but it depends on the use. When I descend I
brake hard, hard enough to at times raise the rear wheel. Therefore, practically my full weight
is on the front. If you are concerned about catastrophic failure or slackening spokes, 36 front
and rear are a good measure. On the other hand, we have seen that 16 front and rear can handle
the job under more ideal conditions. There are 14 spoke wheels as well.

Quoted message said:

Hmmmm, I thought those low spoke count wheels got proportionatly more strength from the rim,
making the spoke count comparison to an open pro moot.

It gets down to two spokes having to support what four to five spokes do in conventional wheels.
Even though 16 spokes seems radical and even more so when "paired" as many are, it is only half of
what most people ride but with rims that are radially substantially stronger... and heavier. Lateral
collapse, the way most wheels fail, is not as good as with more spokes.

Jobst Brandt [email hidden] Palo Alto CA

Mike S.' mikeshaw2@coxDOTnet said:

If you are going to ride 36, I think that the 15/16's will be OK. For the 32 hole front, I'd ride
14/15's. Anything thinner in the front and you may run into problems (unless you go 36 there too).

Right side rear spokes are more highly stressed than front spokes. If there is one place to use a
heavier gauge in a wheelset, it is there.

But none of the spokes in the described wheelset need to be heavier than 15/16ga. Changing the gauge
of the spoke affects its elasticity and its ability to take torque during the tensioning process,
but has little bearing on the strength of a wheel.

I weigh over 350 lbs, and I have used 15/16 and 15/17ga. spokes on the left side of some dished
wheels without ill effects. On wheels with 48 or more spokes, I use only thin spokes if I have
the choice.

Intelligently used, thinner spokes can yield a more durable wheel than thicker ones.

Chalo Colina