slight fork problem - ok or not?

Did you try switching the wheel around to see if the offset was still on the same side of the fork?

"ant" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

got a new fork, some sort of Look carbon blades pretty thing. when i put

a

Quoted message said:

perfectly dished wheel in it the wheel is a bit off to one side, around 2mm to one side near the
brake mounting hole.

i perused the archives, but couldnt find something that mentioned what w3as acceptable
misalignment/fork misconstruction measurements. example:

paul southworth in '93- "One pretty good indicator of mismatched blade lengths is to align the
fork, the stick a known-good front wheel in it (no tire) that is

perfectly

Quoted message said:

dished (ie, no dish at all) and see if the brake bolt-hole in the crown lines up with the center
of the rim (ie, the valve hole). It'll be pretty far off if there is even a millimeter or two of
blade-length discrepancy because the distance from the axle to the rim will effectively exaggerate
the difference."

is my fork fine?based on my unexpert look, id guess that the discrepancy comes from a slightly
less well fit dropout on one side, which

effectively

Quoted message said:

makes one blade a fraction longer. the off-centeredness wont stop me from putting in the tires i
want to use, and i imagine i can adjust the brakes to deal with the small offset, but is there
something i dont know?

and- if i should or can fix this, is a little bit of delicate filing in one drop out (kinesis Al
drops) acceptable? i imagine this would make cnetering the brakes nicer, if the offset didnt
matter for anythign else.

thanks, anthony

"David L. Johnson" <David L. Johnson <[email hidden]>> wrote in message
news:<[email hidden]>...

Quoted message said:

Is the discrepency only in length, or is it out of alignment? My first bike had an
out-of-alignment fork, and I could not ride it no-hands. That would be a good test, if the fork is
on the bike. Line up the wheel properly (centered at the crown), and try to ride no hands. If it
doesn't pull, it should be OK to proceed.

Thanks for the reply- just so im clear, are you suggesting i build the bike up (next week, when i
have everything) and mount the front wheel in the fork in question by putting it fully into the
drops (and letting the small offset be there) or are you suggesting i dont quite let the axle slot
in all the way and tighten the QR so that the wheel is centered at the crown

i suppose this would be kind of like having the flexibility of horizontal dropouts in the rear, but
with the forces workingin the wrong direction. i imagine a good bump will knock the wheel all the
way into the drops and offset the wheel again, but a flat road would work if all i had to do was
check if the bike would track straight.

so- am i checking to see if the bike will ride straight using the dropouts as-is, or am i fudging
the alignment, essentially to see if filing the drops will correct the problem?

thanks,

anthony

"one of the six billion" <[email hidden]> wrote in message
news:<[email hidden]>...

Quoted message said:

Did you try switching the wheel around to see if the offset was still on the same side of
the fork?

heh. yep, did that. good thought, though.

actually- on reinspection, the offset at the crown is probably more like 1mm, but still enough to
visually pick out quite easily, especially since there is little clearance between the rim and
blades. ive stuck a lot of wheels in a lot of forks, and never seen an offset before, which is why i
thought to ask

ant said:

"David L. Johnson" <David L. Johnson <[email hidden]>> wrote in message
news:<[email hidden]>...

Quoted message said:

Is the discrepency only in length, or is it out of alignment? My first bike had an
out-of-alignment fork, and I could not ride it no-hands. That would be a good test, if the fork
is on the bike. Line up the wheel properly (centered at the crown), and try to ride no hands. If
it doesn't pull, it should be OK to proceed.

Thanks for the reply- just so im clear, are you suggesting i build the bike up (next week, when i
have everything) and mount the front wheel in the fork in question by putting it fully into the
drops (and letting the small offset be there) or are you suggesting i dont quite let the axle slot
in all the way and tighten the QR so that the wheel is centered at the crown

The latter. One side, the longer one, will be all the way, and the other will be a slight bit off.

Quoted message said:

i suppose this would be kind of like having the flexibility of horizontal dropouts in the rear,
but with the forces workingin the wrong direction. i imagine a good bump will knock the wheel all
the way into the drops and offset the wheel again,

It would take quite a bump, if the QR is tight. Think about how much force those old horizontal
dropouts could handle.

Quoted message said:

but a flat road would work if all i had to do was check if the bike would track straight.

That's my suggestion.

Quoted message said:

so- am i checking to see if the bike will ride straight using the dropouts as-is, or am i fudging
the alignment, essentially to see if filing the drops will correct the problem?

You're fudging the length. If one fork is forward of the other, then you will still have problems
riding no-hands.

But, if you haven't installed the fork, why not send it back and ask for a new one? After all, it
isn't right, and you paid for it, right? But I would do that before you built it up.

--

David L. Johnson

__o | If all economists were laid end to end, they would not reach a _`\(,_ | conclusion. --
George Bernard Shaw (_)/ (_) |

Quoted message said:

Qui si parla Campagnolo said:

Either misaligned, dropouts aren't parallel or the legs aren't the same

length

Quoted message said:

Quoted message said:

but you should return it. These forks should be more straight than yours

seems

Quoted message said:

Quoted message said:

to be.

"ant" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

What would be considered acceptable offset? As in, measuring from rim to fork blade near the brake
mounting hole how much off can an alignment be before it is not considered normal error? none?

When you drop a wheel into a fork the rim should be visibly centered between the blades. If it is
off, say 0.25mm, you would not be able to see that variance so I would say that's "close enough".

Besides having one blade longer than the other, forks can be awry in lots of other ways. Check the
tips with your H tools. If the ends are not parallel your quick release won't work right and that
alone could account for some misalignmnet of the wheel.

While the tools are in, lay a straightedge across the blades just below the crown. Is it parallel to
the H tools? That is to say, is the fork twisted?

Then sight the length of the fork. Are the blades straight in line with the column all the way to
where the curve starts? Even a minor crash can move the blades back out of line. That would
reduce the rake, but sometimes so slightly the rider doesn't notice until shown the fork on an
alignment plate.

Of course one blade could be bent back more than the other, but you'd notice that riding probably.

Columns can also be bent. A straightedge on the column in a couple of places is a quick way to
know that.

--
Andrew Muzi yellowjersey.orgyellowjersey.orgOpen ↗ Open every day since 1 April 1971

"David L. Johnson" <David L. Johnson <[email hidden]>> wrote in message
news:<[email hidden]>...

Quoted message said:

But, if you haven't installed the fork, why not send it back and ask for a new one? After all, it
isn't right, and you paid for it, right? But I would do that before you built it up.

yes- the trick is that it came from a r.b.market purchase, with a headset and a frame, 'almost
new'. i feel like i got the deal i was looking for for the frameset/hs purchase, but now all i want
to do is return the fork, and i dont know what proportion of the total price that would be.
anyways, its complicated, and between time spent thinking about it, shipping it, cash for shipping,
and finding a new one, i was hoping i could make this one work with a little filing and save myself
some trouble. its not a top of the line fork, nor a top of the line build up, but i dont want it to
be a piece of s*.

thanks for all the help, i will email the seller and ask their advice as well.

cheers anthony