Quick Release to Fixed Hub

icewhain said:

How do I change my front wheel from quick release to bolted? I
thought it would be simple: get a steel skewer the same size as the
quick release one, and put a bolt on either end.

You need to replace the axle with one that extends past the dropouts.
This requires changing out the cones, spacers and lock washers from one
the old axle to the new one (with a conventional hub-cartridge bearing
hubs vary). You'll be able to screw axle *nuts* onto the longer ends.
Just curious, why?

Shawn

"icewhain" <[email hidden]> wrote in message
news:[email hidden]...

Quoted message said:

How do I change my front wheel from quick release to bolted? I
thought it would be simple: get a steel skewer the same size as the
quick release one, and put a bolt on either end.

It is simple but you need to buy a solid axle. They're a bit longer than the
QR ones and are not expensive. You need to then disassemble the hub and swap
the cones, locknuts and other gubbins over to the new axle, taking care to
get the spacing right.

HTH

Andy Chequer

icewhain said:

How do I change my front wheel from quick release to bolted? I
thought it would be simple: get a steel skewer the same size as the
quick release one, and put a bolt on either end.

You can switch to a solid axle as others have suggested, but you can also
get a bolt-in skewer (they use allen bolts). They should be available as a
set (front and rear wheels plus seatpost) at any LBS.

icewhain said:

How do I change my front wheel from quick release to bolted? I
thought it would be simple: get a steel skewer the same size as the
quick release one, and put a bolt on either end.

You can switch to a solid axle as others have suggested, but you can also
get a bolt-in skewer (they use allen bolts). They should be available as a
set (front and rear wheels plus seatpost) at any LBS.

icewhain said:

How do I change my front wheel from quick release to bolted? I
thought it would be simple: get a steel skewer the same size as the
quick release one, and put a bolt on either end.

You can switch to a solid axle as others have suggested, but you can also
get a bolt-in skewer (they use allen bolts). They should be available as a
set (front and rear wheels plus seatpost) at any LBS.

Jacobe Hazzard said:

icewhain said:

How do I change my front wheel from quick release to bolted? I
thought it would be simple: get a steel skewer the same size as the
quick release one, and put a bolt on either end.

You can switch to a solid axle as others have suggested, but you can also
get a bolt-in skewer (they use allen bolts). They should be available as a
set (front and rear wheels plus seatpost) at any LBS.

It should be mentioned that the "leverless" skewers are probably less
secure than a quality steel QR skewer (unless you are talking about
theft, in which case they're more secure). A good QR can apply a
surprising amount of "squeeze" to the dropouts - it's hard (read,
impossible) to duplicate that with the bolted skewers I've seen.

So if the intention was to make the front wheel less likely to
loosen... this may be the wrong direction. If it's to prevent a quick
theft (or even to save a few grams), the leverless skewer might be OK.

Mark Hickey
Habanero Cycles
http://www.habcycles.com
Home of the $695 ti frame

Mark Hickey said:

Quoted message said:

Quoted message said:

How do I change my front wheel from quick release to bolted? I
thought it would be simple: get a steel skewer the same size as the
quick release one, and put a bolt on either end.

You can switch to a solid axle as others have suggested, but you can also
get a bolt-in skewer (they use allen bolts). They should be available as a
set (front and rear wheels plus seatpost) at any LBS.

It should be mentioned that the "leverless" skewers are probably less
secure than a quality steel QR skewer (unless you are talking about
theft, in which case they're more secure). A good QR can apply a
surprising amount of "squeeze" to the dropouts - it's hard (read,
impossible) to duplicate that with the bolted skewers I've seen.

So if the intention was to make the front wheel less likely to
loosen... this may be the wrong direction. If it's to prevent a quick
theft (or even to save a few grams), the leverless skewer might be OK.

Hi. Thanks for all your posts.

I want to change it to prevent theft. So I think I'll go for the
leverless skewer.

Quoted message said:

I want to change it to prevent theft. So I think I'll go for the
leverless skewer.

Wow. They aren't cheap...
http://www.evanscycles.com/product.jsp?style=11069

icewhain said:

Quoted message said:

I want to change it to prevent theft. So I think I'll go for the
leverless skewer.

Wow. They aren't cheap...
http://www.evanscycles.com/product.jsp?style=11069

You can get allen bolt skewers for much less than that. Those skewers are
expensive because of the kryptonite name and because they use special keys
to open and close that provide a slightly greater degree of security. My
experience is that allen bolts are plenty secure, even in high theft
areas, unless you have some pretty shiny wheels.

I've heard a few doubts as to how well the kryptonite levers hold tight.
These are worth checking out: myquicklock.comhowitworks.htmlOpen ↗#
basically quick releases with a detachable lever. Read the article too. Apparently they have 100 different patterns to assure that a thief cant just buy a set and go around snatching up components as usual.
I am seriously considering getting these when I get my nice bike 🙂

quote='Jacobe Hazzard'icewhain said:

Quoted message said:

I want to change it to prevent theft. So I think I'll go for the
leverless skewer.

Wow. They aren't cheap...
evanscycles.comproduct.jspOpen ↗

You can get allen bolt skewers for much less than that. Those skewers are
expensive because of the kryptonite name and because they use special keys
to open and close that provide a slightly greater degree of security. My
experience is that allen bolts are plenty secure, even in high theft
areas, unless you have some pretty shiny wheels.[/QUOTE]

Forgot to mention, it's worth noting their "guarantee." myquicklock.comguarantee.htmlOpen ↗
If your wheels get jacked, you'll get your 45 bucks back if your lucky, otherwise youre SOL on the cost of the components.

JoelM said:

I've heard a few doubts as to how well the kryptonite levers hold tight.
These are worth checking out: myquicklock.comhowitworks.htmlOpen ↗#
basically quick releases with a detachable lever. Read the article too. Apparently they have 100 different patterns to assure that a thief cant just buy a set and go around snatching up components as usual.
I am seriously considering getting these when I get my nice bike 🙂

JoelM said:

I've heard a few doubts as to how well the kryptonite levers hold
tight.

These are worth checking out:
http://www.myquicklock.com/mtbr/howitworks.html#
basically quick releases with a detachable lever. Read the article
too. Apparently they have 100 different patterns to assure that a
thief cant just buy a set and go around snatching up components as
usual.
I am seriously considering getting these when I get my nice bike 🙂

Those look more secure against theft than the kryptonite skewers, which
present a fairly large surface that can be manupulated with ordinary tools
(pliers, screwdriver, etc.)

Jacobe Hazzard said:

Quoted message said:

I've heard a few doubts as to how well the kryptonite levers hold
tight.

These are worth checking out:
http://www.myquicklock.com/mtbr/howitworks.html#
basically quick releases with a detachable lever. Read the article
too. Apparently they have 100 different patterns to assure that a
thief cant just buy a set and go around snatching up components as
usual.
I am seriously considering getting these when I get my nice bike 🙂

Those look more secure against theft than the kryptonite skewers, which
present a fairly large surface that can be manupulated with ordinary tools
(pliers, screwdriver, etc.)

I ordered some from a LBS for £13.99 inc postage. They're allen key
ones, but it's really to prevent opportunists/kids from undoing my
front wheel. (They are not shiny at all).