Ovalized shock mounting holes??

Quoted message said:

Hi All,

I have a Raleigh bike with a Fox Float R rear shock. It seems that the
6mm mounting holes in the rear stay have become slightly ovalized.
This creates a bit of a clunk when the rear end comes of the ground as
the shock then shifts slightly in its mounting holes.

Has anyone got an easy solution to fix this??

Are you sure it's the mounting holes? Old Fox Float shocks have a
bushing that would wear in a few thousand miles causing the exact
symptom you're describing.

Greg

G.T. said:

Quoted message said:

Hi All,

Quoted message said:

I have a Raleigh bike with a Fox Float R rear shock. It seems that the
6mm mounting holes in the rear stay have become slightly ovalized.
This creates a bit of a clunk when the rear end comes of the ground as
the shock then shifts slightly in its mounting holes.

Quoted message said:

Has anyone got an easy solution to fix this??

Are you sure it's the mounting holes? Old Fox Float shocks have a
bushing that would wear in a few thousand miles causing the exact
symptom you're describing.

Greg

Hi Greg

good point...it seems like it is the holes. But I will check the
bushing too...I've done about 2000 miles on the bike...lots of very
bumpy single track so it could well be.

Thanks
Brent

G.T. said:

Quoted message said:

Hi All,

Quoted message said:

I have a Raleigh bike with a Fox Float R rear shock. It seems that the
6mm mounting holes in the rear stay have become slightly ovalized.
This creates a bit of a clunk when the rear end comes of the ground as
the shock then shifts slightly in its mounting holes.

Quoted message said:

Has anyone got an easy solution to fix this??

Are you sure it's the mounting holes? Old Fox Float shocks have a
bushing that would wear in a few thousand miles causing the exact
symptom you're describing.

Greg

Hi Greg.

Well done! there does seem to be some (minimal) ovalizing of the
holes. But the bushing does seem to be what has the most play...not a
major yet, but will be sometime. What is the required fit for those
bushings as I have a lathe and can easily turn some up.

Brent

Quoted message said:

G.T. said:

Quoted message said:

Hi All,
I have a Raleigh bike with a Fox Float R rear shock. It seems that the
6mm mounting holes in the rear stay have become slightly ovalized.
This creates a bit of a clunk when the rear end comes of the ground as
the shock then shifts slightly in its mounting holes.
Has anyone got an easy solution to fix this??

Are you sure it's the mounting holes? Old Fox Float shocks have a
bushing that would wear in a few thousand miles causing the exact
symptom you're describing.

Greg

Hi Greg.

Well done! there does seem to be some (minimal) ovalizing of the
holes. But the bushing does seem to be what has the most play...not a
major yet, but will be sometime. What is the required fit for those
bushings as I have a lathe and can easily turn some up.

I have no idea. I sent mine back to Fox and they fixed it for free.

Greg

G.T. said:

Quoted message said:

G.T. said:

[email hidden] wrote:
> Hi All,
> I have a Raleigh bike with a Fox Float R rear shock. It seems that the
> 6mm mounting holes in the rear stay have become slightly ovalized.
> This creates a bit of a clunk when the rear end comes of the ground as
> the shock then shifts slightly in its mounting holes.
> Has anyone got an easy solution to fix this??
Are you sure it's the mounting holes? Old Fox Float shocks have a
bushing that would wear in a few thousand miles causing the exact
symptom you're describing.

Quoted message said:

Quoted message said:

Greg

Quoted message said:

Hi Greg.

Quoted message said:

Well done! there does seem to be some (minimal) ovalizing of the
holes. But the bushing does seem to be what has the most play...not a
major yet, but will be sometime. What is the required fit for those
bushings as I have a lathe and can easily turn some up.

I have no idea. I sent mine back to Fox and they fixed it for free.

Greg- Hide quoted text -

- Show quoted text -

hmm unfortunately I live in South Africa...will have to see what the
local agents say.

thanks again

Brent

<[email hidden]> wrote in message
news:[email hidden]...

Quoted message said:

G.T. said:

Quoted message said:

On Nov 19, 7:59 pm, "G.T." <[email hidden]> wrote:
> [email hidden] wrote:
>> Hi All,
>> I have a Raleigh bike with a Fox Float R rear shock. It seems that
>> the
>> 6mm mounting holes in the rear stay have become slightly ovalized.
>> This creates a bit of a clunk when the rear end comes of the ground
>> as
>> the shock then shifts slightly in its mounting holes.
>> Has anyone got an easy solution to fix this??
> Are you sure it's the mounting holes? Old Fox Float shocks have a
> bushing that would wear in a few thousand miles causing the exact
> symptom you're describing.

Quoted message said:

> Greg

Quoted message said:

Hi Greg.

Quoted message said:

Well done! there does seem to be some (minimal) ovalizing of the
holes. But the bushing does seem to be what has the most play...not a
major yet, but will be sometime. What is the required fit for those
bushings as I have a lathe and can easily turn some up.

I have no idea. I sent mine back to Fox and they fixed it for free.

Greg- Hide quoted text -

- Show quoted text -

hmm unfortunately I live in South Africa...will have to see what the
local agents say.

thanks again

Brent

Contact Fox. I sent them the information on the shock and bike and they
sent a new bushing set for my bike. Not free but you can still ride while
waiting for the parts to come.

Gary