Newbie Question: Greasing a Seatpost

[email hidden] (Webby) wrote in :"]news:[email hidden]:

Quoted message said:

Can somebody please explain to me what "greasing a seat post" means and why do you do it?

Just wipe a thin coat of grease onto the seat post before inserting it into your frame. Any type of
mechanical grease will do; I use the same stuff I use on my bearings. White lithium auto grease is
always popular.

The grease prevents corrosion, which can be a big problem, especially if the two parts are different
types of metals (steel frame and aluminum seatpost, etc).

Ken

--
rec.bicycles.off-road is moderated by volunteers. To find help solving posting problems, or contact
the moderators, please see rbor.orgrbor.orgOpen ↗ Please read the charter before posting:
rbor.orgrbor charter.txtOpen ↗

Quoted post said:

Originally posted by Ken
[email hidden] (Webby) wrote in :"]news:[email hidden]:

Quoted message said:

Can somebody please explain to me what "greasing a seat post" means and why do you do it?

Just wipe a thin coat of grease onto the seat post before inserting it into your frame. Any type of
mechanical grease will do; I use the same stuff I use on my bearings. White lithium auto grease is
always popular.

The grease prevents corrosion, which can be a big problem, especially if the two parts are different
types of metals (steel frame and aluminum seatpost, etc).

Ken

--

rec.bicycles.off-road is moderated by volunteers. To find help solving posting problems, or contact
the moderators, please see rbor.orgrbor.orgOpen ↗ Please read the charter before posting:
rbor.orgrbor charter.txtOpen ↗

Okay, here we go again, the oldest mistake in engineering is greasing things that should hold together by friction.
For seat-posts, all kinds of threads, stems and handlebars use an anti-seize compound, usually copper-based. The most widely available is made by CRC. Grease is for bearings and other surfaces which should glide against each other.
Let your saddle stay up!
Tell

"Tell" <[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

Okay, here we go again, the oldest mistake in engineering is greasing things that should hold
together by friction. For seat-posts, all kinds of threads, stems and handlebars use an anti-seize
compound, usually copper-based. The most widely available is made by CRC. Grease is for bearings
and other surfaces which should glide against each other. Let your saddle stay up! Tell

Anti-seize is a lubricant, just one that typically uses powdered metal to prevent displacement by
heat and static loads. The problem with seatposts is corrosion, the products of aluminum corrosion
causing the seatpost to effectively swell and lock itself in place. Greased seatposts don't slip if
tight, loose ones will, greased or dry.

On 10 Mar 2003 09:31:22 +1050 Tell said:

Okay, here we go again, the oldest mistake in engineering is greasing things that should hold
together by friction. For seat-posts, all kinds of threads, stems and handlebars use an anti-seize
compound, usually copper-based. The most widely available is made by CRC. Grease is for bearings
and other surfaces which should glide against each other. Let your saddle stay up!

Grease will work fine, as will anti-seize. While this is not a moving part and does not require
lubrication, neither is it a high pressure application where galling is a problem.

A seat tube that is cylindrical and is mated to the proper sized seat post will not slip even if it
is greased, while a seat tube that is out of round and fit to an undersized post will probably slip
even if dry.

The purpose of whatever you put in there is to exclude water and oxygen to prevent corrosion. Most
greases and anti-seizes will do this just fine. The anti-seize DOES have a slight advantage on the
threads of the seat post bolt, however, where the pressures can be higher.

-
-----------------------------------------------
Jim Adney [email hidden] Madison, WI 53711 USA
-----------------------------------------------

Jim Adney said:

The anti-seize DOES have a slight advantage on the threads of the seat post bolt, however, where
the pressures can be higher.

Is that to prevent seizing or to enable the bolt to be tightened further?

~PB

In article said:

Can somebody please explain to me what "greasing a seat post" means and why do you do it?

Most places where you have two metal parts touching each other, and wish to be able to take them
apart again (ever) then some kind of lubrication is a good idea. Seatposts and stems are important
to lubricate because water or sweat can penetrate the area very easily, and stem or seatpost
extraction can be laborious if highly corroded. I usually put a thin film of grease on the seatpost
and then liberally grease the inside of the seat tube as far down as my finger can reach. If you
slather too much on the post it will be wiped off as you insert it. For stems I take it all apart
and grease every part that touches anything (unless it's attached to a carbon-fiber part). Stems
often have a big gap in the steer tube, I like it to be sealed with grease.

--Paul

"Paul Southworth" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

In article said:

Can somebody please explain to me what "greasing a seat post" means and why do you do it?

Most places where you have two metal parts touching each other, and wish to be able to take them
apart again (ever) then some kind of lubrication is a good idea. Seatposts and stems are important
to lubricate because water or sweat can penetrate the area very easily, and stem or seatpost
extraction can be laborious if highly corroded.

Stems often have a big gap in the steer tube, I like it to be sealed with grease.

As Jobst often points out, stems are particularly vulnerable to corrosion (ask me how I know) since
the small movements creates a pumping action that will mix the water with grease over time. The
consequence is that stems should be periodically removed, cleaned and regreased.

Ken said:

[email hidden] (Webby) wrote in :"]news:[email hidden]:

Quoted message said:

Can somebody please explain to me what "greasing a seat post" means and why do you do it?

Just wipe a thin coat of grease onto the seat post before inserting it into your frame. Any type
of mechanical grease will do; I use the same stuff I use on my bearings. White lithium auto grease
is always popular.

The grease prevents corrosion, which can be a big problem, especially if the two parts are
different types of metals (steel frame and aluminum seatpost, etc).

It also keeps it from creaking when you shift your weight. Most "Bottom Bracket" creaks are the
seat post 🙂.

David

11 Mar 2003 14:33:52 -0000 'Pete Biggs said:

Jim Adney said:

The anti-seize DOES have a slight advantage on the threads of the seat post bolt, however, where
the pressures can be higher.

Is that to prevent seizing or to enable the bolt to be tightened further?

Well, I suppose both, but I should add that if the seat tube is reamed properly, and if the seat
post is a proper fit, then it will not be necessary to tighten this bolt very hard. If you find that
you can't get your seat binder bolt tight enough then there is probably a fit problem that you
should get fixed.

-
-----------------------------------------------
Jim Adney [email hidden] Madison, WI 53711 USA
-----------------------------------------------