New pedals and saddle height

"Craig Williams" <[email hidden]> wrote in
:"]news:[email hidden]:

Quoted message said:

After changing from toe clips and straps to Speedplay Zero pedals, I wondered if there is a thumb
rule for saddle height adjustment. I have used the 0.883 X crotch height rule in the past, but I'm
sure it needs some tweaking when changing pedal/cleat/shoe comination.

I think the .883 rule is +/- 1 or 2 cm anyway. If you change your shoes or pedals or even the
thickness of the padding on your shorts, some adjusts may be in order. Many cyclists do raise their
seats during the winter to account for the thickness of winter tights.

Craig Williams said:

After changing from toe clips and straps to Speedplay Zero pedals, I wondered if there is a thumb
rule for saddle height adjustment. I have used the 0.883 X crotch height rule in the past, but I'm
sure it needs some tweaking when changing pedal/cleat/shoe comination.

The problem with the 0.883 "rule" is that it doesn't even take crank length into account. There
are many other variables such as shoe thickness, cleat/pedal stack height, foot size, and
pedaling style. If your seat is too low, you may experience pain at the front of your knees. If
it's too high, your hips will rock. Experiment with heights between those extremes to see what
works best for you.

Art Harris

A bit late now, it seems, but the best approach would have been to measure from your seat along the
seat tube down to the top of your old pedals, then match that distance to the new speedplays,
accommodating for any differences in shoe/cleat thickness. Odds are the speedplays will require a
slight reduction in seat and bar height to maintain your old position.

SB

"Craig Williams" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

After changing from toe clips and straps to Speedplay Zero pedals, I wondered if there is a thumb
rule for saddle height adjustment. I have

used

Quoted message said:

the 0.883 X crotch height rule in the past, but I'm sure it needs some tweaking when changing
pedal/cleat/shoe comination.

Thanks for any help in establishing a new starting point.

Craig [change the VERB to a NUMERAL to reply directly]

"Ken" <[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

"Craig Williams" <[email hidden]> wrote in
:"]news:[email hidden]:

Quoted message said:

After changing from toe clips and straps to Speedplay Zero pedals, I wondered if there is a
thumb rule for saddle height adjustment. I have used the 0.883 X crotch height rule in the past,
but I'm sure it needs some tweaking when changing pedal/cleat/shoe comination.

I think the .883 rule is +/- 1 or 2 cm anyway. If you change your shoes

or

Quoted message said:

pedals or even the thickness of the padding on your shorts, some adjusts

may

Quoted message said:

be in order. Many cyclists do raise their seats during the winter to

account

Quoted message said:

for the thickness of winter tights.

Sure that's not LOWER the saddle? At least that's what I had to do...

Mike

What I recommend is (not my own but most proper saddle height techniques finish up as this).

Sit square, no shoes. Pedal fully down. Bare foot parallel to ground. Heel should be about 5mm
off pedal.

Do this by supporting yourself against a wall and mess around until your heel touches. Then
raise 5mm.

cwilly-<< After changing from toe clips and straps to Speedplay Zero pedals, I wondered if there is
a thumb rule for saddle height adjustment.

Most clip and strap pedals have really close to the spindle design, so I would say just go ride-the
fore-aft/in-out adjustment of the cleat is more important-

Peter Chisholm Vecchio's Bicicletteria 1833 Pearl St. Boulder, CO, 80302
(303)440-3535 vecchios.comvecchios.comOpen ↗ "Ruote convenzionali costruite eccezionalmente bene"