IS PAINT THINNER ANY GOOD?

"Andrew" <[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

I decided to overhaul my hubs, so i needed some solvent. went to home depot asked a guy for
solvent to clean bke parts. sent me to wd40. asked a second guy who said go to paint. asked the
paint guy. sent me to simple green. came back to paint found the solvents. then realized i did not
know which solvent was good. so i bought paint thinner, got tempted by acetone, and an alcohol
which specific name i dont remember. so is thinner good enough to clean bearings cones and axle?
thanks guys

If you're going to use a solvent then it's better to use a fast(er) drying (evaporating) type like
Lacquer thinner or perhaps MEK, just don't take a big whiff of it. Acetone is too fast. Also, keep
it away from any plugged-in electrical appliances or open flames. This sounds like common sense, but
trust me, I used to paint houses.

Personally, I find the citrus type/simple green cleaners much more user friendly and versatile.

--
Slacker

I always have used and still use Kerosene. I go through about a gallon every 3-4 years. Works great
and is much safer then using gas. "Andrew" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

I decided to overhaul my hubs, so i needed some solvent. went to home

depot

Quoted message said:

asked a guy for solvent to clean bke parts. sent me to wd40. asked a

second

Quoted message said:

guy who said go to paint. asked the paint guy. sent me to simple green.

came

Quoted message said:

back to paint found the solvents. then realized i did not know which

solvent

Quoted message said:

was good. so i bought paint thinner, got tempted by acetone, and an alcohol which specific name i
dont remember. so is thinner good enough to clean bearings cones and axle? thanks guys

dang X posters!!! ughhh

Andrew said:

I decided to overhaul my hubs, so i needed some solvent. went to home depot asked a guy for
solvent to clean bke parts. sent me to wd40. asked a second guy who said go to paint. asked the
paint guy. sent me to simple green. came back to paint found the solvents. then realized i did not
know which solvent was good. so i bought paint thinner, got tempted by acetone, and an alcohol
which specific name i dont remember. so is thinner good enough to clean bearings cones and axle?
thanks guys

kerosene, gasolene are good, MEK and the fast eveporators are a little hard to work with ( unless
you want to huff them while you work). simple green works well on light degreasing jobs but it and
other 'degreasers' can harm the finish on aluminum; if you use it wash it off quickly.

"Andrew" <[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

I decided to overhaul my hubs, so i needed some solvent. went to home

depot

Quoted message said:

asked a guy for solvent to clean bke parts. sent me to wd40. asked a

second

Quoted message said:

guy who said go to paint. asked the paint guy. sent me to simple green.

came

Quoted message said:

back to paint found the solvents. then realized i did not know which

solvent

Quoted message said:

was good. so i bought paint thinner, got tempted by acetone, and an alcohol which specific name i
dont remember. so is thinner good enough to clean bearings cones and axle? thanks guys

Diesel works pretty good for me...
--
Westie

Andrew said:

so i bought paint thinner, got tempted by acetone, and an alcohol which specific name i dont
remember.

This could almost be a story from any housing scheme in Glasgow in the 80s or
90s.

Andrew said:

I decided to overhaul my hubs, so i needed some solvent. went to home depot asked a guy for
solvent to clean bke parts. sent me to wd40. asked a second guy who said go to paint. asked the
paint guy. sent me to simple green. came back to paint found the solvents. then realized i did not
know which solvent was good.

There are lots of paint thinners. Turpentine seems to stick around a lot, so may not be the best. I
sometimes use kerosene; it's cheap, and is an effective solvent for grease and such.

But mostly I use Simple Green. It is not as cheap, but less volatile, and works fine.

--

David L. Johnson

__o | If all economists were laid end to end, they would not reach a _`\(,_ | conclusion. --
George Bernard Shaw (_)/ (_) |

James Connell said:

kerosene, gasolene are good,

Do not use gasoline as a solvent. It is too volatile, and can easily ignite from small sparks. That
is how a car works, guys. Also, there are additives that are designed to stick to the surfaces,
which is not what you want for cleaning.

--

David L. Johnson

__o | Do not worry about your difficulties in mathematics, I can _`\(,_ | assure you that mine
are all greater. -- A. Einstein (_)/ (_) |

On Wed, 02 Apr 2003 00:26:35 -0500, "David L. Johnson" <[email hidden]> scribbled:

Quoted message said:

James Connell said:

kerosene, gasolene are good,

Do not use gasoline as a solvent. It is too volatile, and can easily ignite from small sparks. That
is how a car works, guys. Also, there are additives that are designed to stick to the surfaces,
which is not what you want for cleaning.

Flaming mountain bikers - imagine the environmental impact! 😉

-Slash
--
"Ebert Victorious"

- The Onion

Slash said:

On Wed, 02 Apr 2003 00:26:35 -0500, "David L. Johnson" <[email hidden]> scribbled:

Quoted message said:

James Connell said:

kerosene, gasolene are good,

Do not use gasoline as a solvent. It is too volatile, and can easily ignite from small sparks.
That is how a car works, guys. Also, there are additives that are designed to stick to the
surfaces, which is not what you want for cleaning.

Flaming mountain bikers - imagine the environmental impact! 😉

-Slash
--
"Ebert Victorious"

- The Onion

Flaming mountain bikers? I thought it was usually the roadies who were flaming...

Jon Bond yeah, so I have a road bike, what of it? Technically its not mine 😉

"Andrew" <[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

I decided to overhaul my hubs, so i needed some solvent. went to home

depot

Quoted message said:

asked a guy for solvent to clean bke parts. sent me to wd40. asked a

second

Quoted message said:

guy who said go to paint. asked the paint guy. sent me to simple green.

came

Quoted message said:

back to paint found the solvents. then realized i did not know which

solvent

Quoted message said:

was good. so i bought paint thinner, got tempted by acetone, and an alcohol which specific name i
dont remember. so is thinner good enough to clean bearings cones and axle? thanks guys

Any of those will clean out the grease and crud. Be sure to thoroughly remove all the grit and rinse
out any stuff inthe threads of the axle too.

--
Andrew Muzi yellowjersey.orgyellowjersey.orgOpen ↗ Open every day since 1 April 1971

David L. Johnson said:

James Connell said:

kerosene, gasolene are good,

Do not use gasoline as a solvent. It is too volatile, and can easily ignite from small sparks.
That is how a car works, guys. Also, there are additives that are designed to stick to the
surfaces, which is not what you want for cleaning.

gas is a great grease buster one of the best there is. it is cheap (or at least it was) and most
people have it around. the little bit of additive left over hurts nothing and will wash off with
'soft' degreaser. if you are worried about blowing yourself up i don't recommend you attempt
mecanical repairs.

Not in a martini. For that, I prefer Bombay Sapphire. I've tried other gins, but they taste a bit
too much like paint thinner.

Andrew said:

I decided to overhaul my hubs, so i needed some solvent. went to home depot asked a guy for
solvent to clean bke parts. sent me to wd40. asked a second guy who said go to paint. asked the
paint guy. sent me to simple green. came back to paint found the solvents. then realized i did not
know which solvent was good. so i bought paint thinner, got tempted by acetone, and an alcohol
which specific name i dont remember. so is thinner good enough to clean bearings cones and axle?
thanks guys

I use WD-40 here.

David

David L. Johnson <[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

James Connell said:

kerosene, gasolene are good,

Do not use gasoline as a solvent. It is too volatile, and can easily ignite from small sparks.
That is how a car works, guys. Also, there are additives that are designed to stick to the
surfaces, which is not what you want for cleaning.

You'd have to be pretty stupid to blow yourself up using petrol as a cleaner - just make sure you do
it outside and away from sources of ignition. Any residues left will be totally harmless to your
bearings/other metal parts - you think they'd put anything in petrol that would damage contacting
and moving metal parts? Then why TF would they have it going into a car engine?!?

HTH,

Shaun aRe

"Andrew" <[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

I decided to overhaul my hubs, so i needed some solvent. went to home

depot

Quoted message said:

asked a guy for solvent to clean bke parts. sent me to wd40. asked a

second

Quoted message said:

guy who said go to paint. asked the paint guy. sent me to simple green.

came

Quoted message said:

back to paint found the solvents. then realized i did not know which

solvent

Quoted message said:

was good. so i bought paint thinner, got tempted by acetone, and an alcohol which specific name i
dont remember. so is thinner good enough to clean bearings cones and axle? thanks guys

WD40

--
DTW .../\.../\.../\...

Robert Chung said:

Not in a martini. For that, I prefer Bombay Sapphire. I've tried other gins, but they taste a bit
too much like paint thinner.

Be honest - you only buy the Sapphire for the bottle. Feckin' poseurs! ;-))

Steve

James Connell said:

kerosene, gasolene are good,

Please don't use gasoline for anything but a fuel.

There are so many other good solvents that don't have fumes that cling to humans and explode.
Kerosene, citrus solvents, mineral spirits, etc... are cheap and much safer.

Barry

"D T W .../\..." <[email hidden]> wrote in message
"]news:[email hidden]...
| "Andrew" <[email hidden]> wrote in message "]news:[email hidden]...
| > I decided to overhaul my hubs, so i needed some solvent. went to home
| depot
| > asked a guy for solvent to clean bke parts. sent me to wd40. asked a
| second
| > guy who said go to paint. asked the paint guy. sent me to simple green.
| came
| > back to paint found the solvents. then realized i did not know which
| solvent
| > was good. so i bought paint thinner, got tempted by acetone, and an alcohol which specific name
| > i dont remember. so is thinner good enough to clean bearings cones and axle? thanks guys
| >
|
|
| WD40
|
| --
| DTW .../\.../\.../\...
Not sure what you are meaning but if its cleaning of greased parts then it is obvious to use a
degreaser....... I use Gunk! Most car/automobile shops will have this so too will most motocross
shops. Just brush on leave for a few mins then rinse. After that totally regrease all parts needed.

Simon.........did I miss the point?