fixed wheel chain choice

Alex Graham said:

I'm putting together a fixed wheel bike out of an old 'Raleigh Pioneer Classic'. I was given a 52T
chainset by someone, which was convenient.

Actually, that's not so convenient as you might suppose, because for road-worthy gearing it requires
a rather large rear sprocket, typically 19 or 20. I generally recommend a 42 or thereabouts for a
road fixer.

Quoted message said:

its the exact same one as on my normal bike, which uses a 3/32 chain, however ive beed advised to
use a 1/8th chain, which is wider.

That's not the best advice I've ever heard.

Quoted message said:

So what I am confused about is:

Can I use this 1/8th chain on my normal (3/32??) chainring?

Yep.

Quoted message said:

And presumably do I need a 1/8th rear sprocket?

Nope. 1/8" chain works on either size sprockets, but if both sprockets are 3/32", you'd be better
off sticking to 3/32" chain.

For lotsa stuff about fixed-gear bikes, see:

sheldonbrown.comfixedOpen ↗

Sheldon "If It Isn't Fixed, It's Broken!" Brown
+----------------------------------------------------+
| I admit that reason is a small and feeble flame, | a flickering torch by stumblers carried in the
| | star-less night, -- blown and flared by passion's | storm, -- and yet, it is the only light. |
| Extinguish that, and nought remains. | -- Robert Green Ingersoll |
+----------------------------------------------------+ Harris Cyclery, West Newton, Massachusetts
Phone 617-244-9772 FAX 617-244-1041 harriscyclery.comharriscyclery.comOpen ↗ Hard-to-find parts shipped Worldwide
captainbike.comcaptainbike.comOpen ↗ sheldonbrown.comsheldonbrown.comOpen ↗

Would you not recommend 1/8 at all then? I was told it was wider and hence 'lasts a bit longer' not
sure how true that is though.

The chainring is sort of convenient as I'm a student and hence cheapskate :o) I was see it isnt
ideal though.

--
-Alex

----------------------------------
[email hidden] www.westerleycycling.org.uk alexpg.ath.cxcycling.phpOpen ↗
----------------------------------

Alex Graham said:

Hi,

I'm putting together a fixed wheel bike out of an old 'Raleigh Pioneer Classic'. I was given a 52T
chainset by someone, which was convenient. Now its the exact same one as on my normal bike, which
uses a 3/32 chain, however ive beed advised to use a 1/8th chain, which is wider. So what I am
confused about is:

Can I use this 1/8th chain on my normal (3/32??) chainring?

And presumably do I need a 1/8th rear sprocket? Does this apply to chainrings too (hence question
above 🙂

If you use a 1/8" wide sprocket, you will need 1/8" chain. This is what I do, since I have lots of
sprockets collected since the 70s. But there are plenty of 3/23" sprockets sold. Get them, and you
can use a 3/32" chain (8-speed, 9-speed, it doesn't matter).

--

David L. Johnson

__o | "A foolish consistency is the hobgoblin of little minds, adored _`\(,_ | by little
statesmen and philosophers and divines." --Ralph Waldo (_)/ (_) | Emerson

Alex Graham said:

Would you not recommend 1/8 at all then? I was told it was wider and hence 'lasts a bit longer'
not sure how true that is though.

Poppycock. A fixed-gear chain will outlast a derailleur chain by a fair amount, but not because of
its width. The difference is that the fixed gear always has a good chainline, while a derailleur
bike typically runs with a bad chainline. The 1/8" width will not significantly contribute to longer
chain life. Chains wear out due to friction against all the pins and plates. Wider pins have more
area to wear, but proportionally more grit in there wearing it away, also.

Quoted message said:

The chainring is sort of convenient as I'm a student and hence cheapskate :o) I was see it isnt
ideal though.

I'd say that the 52 is a bit big, but if you can find a good size cog to go with it, then it should
be fine. Larger cogs/chainrings do last longer, for a number of reasons.

--

David L. Johnson

__o | When you are up to your ass in alligators, it's hard to remember _`\(,_ | that your initial
objective was to drain the swamp. -- LBJ (_)/ (_) |

"Alex Graham" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

Hi,

I'm putting together a fixed wheel bike out of an old 'Raleigh Pioneer Classic'. I was given a 52T
chainset by someone, which was convenient. Now its the exact same one as on my normal bike, which
uses a 3/32 chain, however ive beed advised to use a 1/8th chain, which is wider. So what I am
confused about is:

Can I use this 1/8th chain on my normal (3/32??) chainring?

And presumably do I need a 1/8th rear sprocket? Does this apply to chainrings too (hence question
above 🙂

BMX 1/8" chains are cheap and may be run on 3/32 or 1/8 teeth or a combination of them. Since many
of us relegate our fixed bikes to poor weather this allows more frequent (less expensive) chain
replacement.

--
Andrew Muzi yellowjersey.orgyellowjersey.orgOpen ↗ Open every day since 1 April 1971

I have a british 1930 era flip flop track hub. It takes standard cogs, but the lock ring is not
standard threaded. I have one old lock ring that I use for the big cog. I don't have one for the
little cog on the other side. (I probably won't use that little cog, I'm not man enough ha ha). Is
there a source for odd track lock rings?
--
Bill "Pop Pop" Patterson Retired and riding my Linear, my front drive low racer our M5 tandem and my
old Schwinn Paramount.

See some Bikes At:

home.earthlink.netindex.htmlOpen ↗

Reply to [email hidden]

alex-<< I'm putting together a fixed wheel bike out of an old 'Raleigh Pioneer Classic'. I was given
a 52T chainset by someone, which was convenient. Now its the exact same one as on my normal bike,
which uses a 3/32 chain, however ive beed advised to use a 1/8th chain, which is wider. So what I am
confused about is:

No need to use a track chain(1/8"😉 altho it'll work.

Peter Chisholm Vecchio's Bicicletteria 1833 Pearl St. Boulder, CO, 80302
(303)440-3535 vecchios.comvecchios.comOpen ↗ "Ruote convenzionali costruite eccezionalmente bene"

I put an old 1/8" chain on my fixie (with 3/32" chainring & sprocket) when I first built it up,
since I needed a chain and had a shortish 1/8" lying around.

It worked OK, but after several rides I replaced it with a 3/32" chain and the drive train became
smoother and quieter.

Chain wear is negligible because the chainline is straight. I must have ~3k miles on the current
chain (Sedis PCS-68) with hardly any "stretch".

Gearing-wise, I use 42/16 which is about average for flat to rolling terrain.

Mike Yankee

(Address is munged to thwart spammers. To reply, delete everything after "com".)