fh-7800 hub dimensions

"Eric" <[email hidden]> wrote in message news:<[email hidden]>...

Quoted message said:

I want to built up one of these hubs and would like the
dimensions to enter into a spoke calculator. I use the
spocalc.exe. I need center to each flange distance and
flange diameter. Thanks Eric

Hi, the specs are on this website: dura-dura-Open ↗
ace.com/publish/content/duraace/en/home/the_product0/w-
heels.html

Life is Good! Jeff

<< Hi, the specs are on this website:
dura-ace.comwheelOpen ↗
s.html

Quoted message said:

Quoted message said:

<BR><BR>

Doesn't gibe flange diameter or center to flange...tho-I
think the same as 7700 hubs tho-

REMEMBER-10s cogsets only!!

Peter Chisholm Vecchio's Bicicletteria 1833 Pearl St.
Boulder, CO, 80302
(303)440-3535 vecchios.comvecchios.comOpen ↗ "Ruote convenzionali
costruite eccezionalmente bene"

Quoted post said:

Originally posted by Jeff Starr
"Eric" <[email hidden]> wrote in message news:<[email hidden]>...

Quoted message said:

I want to built up one of these hubs and would like the
dimensions to enter into a spoke calculator. I use the
spocalc.exe. I need center to each flange distance and
flange diameter. Thanks Eric

Hi, the specs are on this website: dura-dura-Open ↗
ace.com/publish/content/duraace/en/home/the_product0/w-
heels.html

Life is Good! Jeff

Life may be good, but the URL you gave isn't.
Hole PCD 44mm
Flange Distance 56.9
Dish 7.9
From:
http://tinyurl.com/yqzem
or if you can cut and paste the original too long URL:
http://www.dura-ace.com/publish/content/duraace/en/home/the_
product0/wheels.ExtraMainContentPar.0007.File.tmp/FH7800_spe
c.pdf
I agree with Peter Chisholm. The flanges are larger, spacing slightly different, spoke hole diameter is identical.
When I look at the current version that Sheldon Brown carries on his web site I see the FH-7800 hub with correct dimensions listed.
If you saved an older version you should revisit the site and get the new chart.

[email hidden] (Qui si parla Campagnolo ) wrote in message news:<[email hidden]>...

Quoted message said:

<< Hi, the specs are on this website: dura-dura-Open ↗
ace.com/publish/content/duraace/en/home/the_product0/wheel
s.html

Quoted message said:

Quoted message said:

<BR><BR>

Doesn't gibe flange diameter or center to flange...tho-I
think the same as 7700 hubs tho-

REMEMBER-10s cogsets only!!

Peter Chisholm Vecchio's Bicicletteria 1833 Pearl St.
Boulder, CO, 80302
(303)440-3535 vecchios.comvecchios.comOpen ↗ "Ruote convenzionali
costruite eccezionalmente bene"

Peter, did you try clicking on pdf files at bottom of page,
where it has the links - FH-7800 Specifications and HB-7800
Specifications? The info might be in there. I ordered the
back hub [DA FH-7700] for the wheels I am going to have
built. It looks like June, for enough funds to have you do
the work. I'll be in touch.

Life is Good! Jeff

[email hidden] (Qui si parla Campagnolo ) wrote in message news:<[email hidden]>...

Quoted message said:

<< Hi, the specs are on this website: dura-dura-Open ↗
ace.com/publish/content/duraace/en/home/the_product0/wheel
s.html

Quoted message said:

Quoted message said:

<BR><BR>

Doesn't gibe flange diameter or center to flange...tho-I
think the same as 7700 hubs tho-

REMEMBER-10s cogsets only!!

dura-dura-Open ↗
ace.com/publish/content/duraace/en/home/the_product0/wheels-
.ExtraMainContentPar.0007.File.tmp/FH7800_spec.pdf

shows that flange diameter is 44mm. Distance to right flange
is 49mm. Distance to left flange is 64.8mm.

I'd be willing to bet that these figures are within a couple
tenths of a millimeter of the FH-7700 hub.

Jeff