Cateye Mity 8 Computer

"Mary" <[email hidden]> wrote in message
news:[email hidden]...

Quoted message said:

Recently purchased this computer. For the life of me I cannot figure out
how far down the fork to put the sensor. When I mounted my last computer
it was clearly outlined in the directions. Have looked online but to no
avail. Anyone use this computer? Thanks

It doesn't matter. A rev is a rev is a rev.

RichC

Rich Clark said:

"Mary" <[email hidden]> wrote in message
news:[email hidden]...

Quoted message said:

Recently purchased this computer. For the life of me I cannot figure out
how far down the fork to put the sensor. When I mounted my last computer
it was clearly outlined in the directions. Have looked online but to no
avail. Anyone use this computer? Thanks

It doesn't matter. A rev is a rev is a rev.

Themagnetically induced spike's amplitude is related to, among other
things, velocity. If mounted too close to the hub, the sensor may
miss pulses at low speeds.
About halfway out should be fine.

NanC said:

Rich Clark said:

"Mary" <[email hidden]> wrote in message
news:[email hidden]...

Quoted message said:

Recently purchased this computer. For the life of me I cannot figure out
how far down the fork to put the sensor. When I mounted my last computer
it was clearly outlined in the directions. Have looked online but to no
avail. Anyone use this computer? Thanks

It doesn't matter. A rev is a rev is a rev.

Themagnetically induced spike's amplitude is related to, among other
things, velocity. If mounted too close to the hub, the sensor may
miss pulses at low speeds.
About halfway out should be fine.

Except the Cateye's sensor is a simple magnetic reed switch; there is no
"induced spike", just a contact closure that will not be significantly
dependent on the speed of the passing magnet. (The only computers I am
aware of that do depend on induced signals are the Avocets, and they use
a 20-pole magnet ring mounted at the hub.)

Responding to the original poster, if there is no limitation to where
you have to put the wheel magnet (IIRC some Cateyes had a magnet carrier
which wrapped around two spokes, so the magnet and sensor had to go
about mid-wheel), I'd put it as close to the hub as you can get it,
mostly because that lets you tuck the sensor in back of the fork blade
instead of having it stick out toward the spokes.

Don Piven said:

NanC said:

Rich Clark said:

"Mary" <[email hidden]> wrote in message
news:[email hidden]...
> Recently purchased this computer. For the life of me I cannot figure out
> how far down the fork to put the sensor. ...
It doesn't matter. A rev is a rev is a rev.

Themagnetically induced spike's amplitude is related to, among other
things, velocity. If mounted too close to the hub, the sensor may
miss pulses at low speeds.
About halfway out should be fine.

Except the Cateye's sensor is a simple magnetic reed switch; there is no
"induced spike", just a contact closure that will not be significantly
dependent on the speed of the passing magnet. ...
Responding to the original poster, if there is no limitation to where
you have to put the wheel magnet

The OP asked how far down to mount the sensor. The answer is just far
enough down to align with the magnet.

Mounting higher than the point at which the rim passes betwen the forks
will unnecessarily complicate mounting the magnet, as will mounting
below the o/s diameter of the hub flange

best wishes
james

I've always been told to mount it as close to the hub as possible. The
reasoning behind this is that the closer the magnet is to the center, the
slower it will turn. With the magnet mounted closer to the rim this could
cause erratic readings at higher speeds since the magnet passes the sensor
much faster. I haven't experimented with this but it does make sense.

"Mary" <[email hidden]> wrote in message
news:[email hidden]...

Quoted message said:

Recently purchased this computer. For the life of me I cannot figure out
how far down the fork to put the sensor. When I mounted my last computer
it was clearly outlined in the directions. Have looked online but to no
avail. Anyone use this computer? Thanks