Bontrager Wheels--durability

I own a Trek 2300 with the same wheel set and haven't had any problems with broken spokes. The
spokes aren't standard so replacement could take awhile if you break one but I'd expect you could
ride the wheel on the day the spoke breaks without damaging the wheel. Wouldn't recommend continuing
to ride the wheel until the spoke was replaced. Same thing applies for standard spoked wheels.

"James Cassatt" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

I am about to take delivery of a new TREK 5200. It comes with Bontrager RaceLite Wheels
standard--20 h front, 24 h rear. My fear is that I might be stranded by a broken spoke 50 miles
from home. When I have broken spokes with "ordinary" spoked wheels, I have been able to tweak the
spokes and get home. It looks to me as if the Bontragers would be unridable in the event of a
broken spoke. My questions then:

Are they unridable in the event of a broken spoke? What are the chances of a spoke breaking
compared to ordinary spoked wheels? If I carry extra spokes and the appropriate tools, can repairs
be done in the field?

As far as my riding, I am 6' 180 lbs. While I don't hammer, I do ride a lot on multi-user trails
and biker friendly streets. These venues can be a bit rough.

In trying to find answers on Google, I have found a lot on conjectures but little hard data. Hence
I would especially like to hear from those with actual experience with these wheels.

Thanks

Jim

Quoted message said:

Are they unridable in the event of a broken spoke?

From the examples I've seen (just a couple, where people had picked up a stick etc. from the road
and tossed it into a wheel), a Bontrager wheel doesn't come out of true much differently than a
32-spoke wheel would. There's enough clearance both front & rear on the 5200 frame that it shouldn't
be a problem.

Even the older Rolf Vector Pro wheels, which were built much less conservatively and known to break
a spoke one in a while, still passed through the frame with a broken spoke... and those only had 16
rear and 14 front. It's something of a myth that low-spoke-count wheels are rendered unrideable from
a single failed spoke. It's also a myth that a 32 or 36-spoke wheel is immune to such problems. In
the real world, there doesn't seem to be a correlation between spoke count and how far out of whack
they get from a single spoke failure. I suspect it has more to do with rim strength than spokes.

Quoted message said:

What are the chances of a spoke breaking compared to ordinary spoked wheels?

So far, nil. We sell a very large number of bikes with Bontrager low-spoke-count wheels (the Race
Lite and Race X-Lite models) and spoke breakage simply doesn't occur. They're in their third year
now, so it's not something new & untested. They're boring to the mechanics, which is a good thing.
They just simply do their job without fanfare.

Quoted message said:

If I carry extra spokes and the appropriate tools, can repairs be done in the field?

They're basically standard spokes & nipples, and there's nothing more difficult about truing
a paired-spoke wheel than a conventional one. But it's really not likely you'll need to
worry about it.

--Mike-- Chain Reaction Bicycles chainreactionbicycles.comchainreactionbicycles.comOpen ↗

Quoted message said:

I own a Trek 2300 with the same wheel set and haven't had any problems

with

Quoted message said:

broken spokes. The spokes aren't standard so replacement could take

awhile

Quoted message said:

if you break one but I'd expect you could ride the wheel on the day the spoke breaks without
damaging the wheel. Wouldn't recommend continuing to ride the wheel until the spoke was replaced.
Same thing applies for standard spoked wheels.

While the spokes in a Bontrager RaceLite (or Race X-Lite) are bladed, you can substitute any garden
variety spoke of the correct length with no trouble at all. Fortunately, the need to do so is
exceptionally rare, as the only way you're likely to break a spoke is if you pick up a stick from
the road and toss it into the wheel.

--Mike-- Chain Reaction Bicycles chainreactionbicycles.comchainreactionbicycles.comOpen ↗

I purchased a Trek 5200 last March with Bontrager Race Lite Wheels, I have 3400 miles and have never
touched or had a problem with the wheels. They are as true today as the day I took delivery of the
bike. I ride pretty hard and weigh 165 lbs. Average about 20 mph. You made a great choice with that
bike. Good Luck.

"James Cassatt" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

I am about to take delivery of a new TREK 5200. It comes with Bontrager RaceLite Wheels
standard--20 h front, 24 h rear. My fear is that I might be stranded by a broken spoke 50 miles
from home. When I have broken spokes with "ordinary" spoked wheels, I have been able to tweak the
spokes and get home. It looks to me as if the Bontragers would be unridable in the event of a
broken spoke. My questions then:

Are they unridable in the event of a broken spoke? What are the chances of a spoke breaking
compared to ordinary spoked wheels? If I carry extra spokes and the appropriate tools, can repairs
be done in the field?

As far as my riding, I am 6' 180 lbs. While I don't hammer, I do ride a lot on multi-user trails
and biker friendly streets. These venues can be a bit rough.

In trying to find answers on Google, I have found a lot on conjectures but little hard data. Hence
I would especially like to hear from those with actual experience with these wheels.

Thanks

Jim

[email hidden] (James Cassatt) writes:

| I am about to take delivery of a new TREK 5200. It comes with Bontrager RaceLite Wheels
| standard--20 h front, 24 h rear. My fear is that I might be stranded by a broken spoke 50 miles
| from home. When I have broken spokes with "ordinary" spoked wheels, I have been able to tweak the
| spokes and get home. It looks to me as if the Bontragers would be unridable in the event of a
| broken spoke. My questions then:

I've put over 10,000 miles on my 5500 bought in January 2002 (same wheels), and never broken a
spoke, riding some moderately rough roads, and plenty of potholes, and one accident hitting a curb
at speed. I'm currently at 200 pounds, but was at 230 when I bought the bike.

I did bust the right chainstay, just pulling away from a stop sign, but it's apparently delayed
damage from a moderately nasty accident a year earlier. I had the bike checked out afterwards, but
nothing was spotted. The break (straight through, completely unridable) was right under the decal in
front of the derailleur, so it might have been tough to see right after it happened. (Of course, I
look the bike over moderately carefully from time to time, most recently several weeks before the
breakage, and hadn't spotted anything then, either.) That problem is costing me $600 to get
repaired, and a couple of months riding a borrowed bike.

I will say that I love the ride of the 5500/5200, and don't regret buying it for a moment.

The spokes should be easily replaceable if they do break, but I can't yet confirm it from actual
experience.

Dave Olson [email hidden] unixfolk.comdaveOpen ↗

I've ridden over 75,000 miles in my life and only had one broken spoke. Wouldn't expect to break one
on the 2300 unless a pot hole caught me by surprise. This bike is sweet. My previous bike was a Trek
1500 from 88 and I'm at least 1 mph faster on the 2300 for the same effort.

"Mike Jacoubowsky" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

Quoted message said:

I own a Trek 2300 with the same wheel set and haven't had any problems

with

Quoted message said:

broken spokes. The spokes aren't standard so replacement could take

awhile

Quoted message said:

if you break one but I'd expect you could ride the wheel on the day the spoke breaks without
damaging the wheel. Wouldn't recommend continuing

to

Quoted message said:

Quoted message said:

ride the wheel until the spoke was replaced. Same thing applies for standard spoked wheels.

While the spokes in a Bontrager RaceLite (or Race X-Lite) are bladed, you can substitute any
garden variety spoke of the correct length with no trouble at all. Fortunately, the need to do so
is exceptionally rare, as the only way you're likely to break a spoke is if you pick up a stick
from the road and toss it into the wheel.

--Mike-- Chain Reaction Bicycles chainreactionbicycles.comchainreactionbicycles.comOpen ↗

Bill Brunning said:

I've ridden over 75,000 miles in my life and only had one broken spoke. Wouldn't expect to break
one on the 2300 unless a pot hole caught me by surprise. This bike is sweet. My previous bike was
a Trek 1500 from 88 and I'm at least 1 mph faster on the 2300 for the same effort.

I don't know the circumstances (your weight, where you ride and what sort of wheels you use) but
that seems unusual for anyone other than a classic 97lb weakling from:

charlesatlas.comcharlesatlas.comOpen ↗

What do you believe breaks spokes? You mention a pot hole. Do you have any idea what sort of loads
striking a pot hole puts on spokes?

Jobst Brandt [email hidden] Palo Alto CA

Just to provide some balance to this thread, I have replaced a broken spoke on a _front_ Bontrager
Race Lite wheel. It was ridable before the replacement, and still is - though I don't personally own
this wheel (my commuter front wheel has 36 spokes, so everyone can just relax, OK?).

--
==================
Kraig Willett www.biketechreview.com
==================

Quoted message said:

What do you believe breaks spokes? You mention a pot hole. Do you have any idea what sort of loads
striking a pot hole puts on spokes?

Tell us. I broke some spokes doing stupid stuff like going down stairs on my 700x25 wheels, but the
wheel was FUBARed long before that because I had bought it used from a bum. Someone had broken the
spokes, replaced them with aero spokes on half of them with a wrong cross pattern (like half radial
and half 3-cross on the same side of one wheel), and used crappy stainless spokes that, when
removed, would actually fail without bending first. All the spokes I broke were those crappy spokes.
I bought a set of 32 used DTs from my LBS for $2 to replace the [censored] spokes. I guess you could say
that I was acutely stress-relieving the wheels.

Jobst, what causes the indentations from the spokes that cross each other? Are they caused by minute
rubbing motions from road vibration? I ask because those replacement DT spokes had pretty deep
indentations in them when I got them and I'm wondering if they're to be a concern in the long term.

It's great though because everything on the bum bike (Giant Kronos) was straight, even the
nonreplaceable derailleur hangar. I slapped on new cables/housing/bars/saddle, and my $65 bike is as
good as the day it rolled out of the factory.

--
Phil, Squid-in-Training

[email hidden] (James Cassatt) wrote in message
news:<[email hidden]>...

Quoted message said:

As far as my riding, I am 6' 180 lbs. While I don't hammer, I do ride a lot on multi-user trails
and biker friendly streets. These venues can be a bit rough.

Hi James,

I bought a 2003 5200 last August and have ridden over 2000mi so far (CTS. Be like Lance!). I am also
180 lbs and so far have had no broken spokes, though I am about to undertake building my first set
of wheels and hope to learn how to true both the Bontragers and the Mavic's on my backup Bianchi
Vigorelli.

I did have an accident where a pedestrian steped in front of me without looking and I hit him going
about 20mph. The Bontrager and my left shin had a discussion and the Bontrager gave way. Perhaps not
quite the same as a broken spoke, but the wheel was a total loss. Better that than my leg, though.

HTH,

Byron

I'm a 165 lb. rider now who hasn't kept an official count so it could have been as many as three
rather than one but I know the frequency of breaking spokes for me is rare... hasn't happened in the
past 10 years.

<[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

Bill Brunning said:

I've ridden over 75,000 miles in my life and only had one broken spoke. Wouldn't expect to break
one on the 2300 unless a pot hole caught me by surprise. This bike is sweet. My previous bike
was a Trek 1500 from 88 and I'm at least 1 mph faster on the 2300 for the same effort.

I don't know the circumstances (your weight, where you ride and what sort of wheels you use) but
that seems unusual for anyone other than a classic 97lb weakling from:

charlesatlas.comcharlesatlas.comOpen ↗

What do you believe breaks spokes? You mention a pot hole. Do you have any idea what sort of loads
striking a pot hole puts on spokes?

Jobst Brandt [email hidden] Palo Alto CA

Quoted message said:

Had you read about what causes spoke failure, you could have saved yourself some trouble. Riding
down stairs does not cause spoke failure. This is unique event among millions of stress cycles
that cause spoke fatigue and do not have an effect on spoke life. Besides, spoke tension is
reduced by a wheel impact. Spoke tension is highest in an unloaded wheel at rest. When the wheel
is loaded, only spokes in the road contact patch have their tension reduced while the others
remain unchanged. A small increase in tension, insignificant to the static tension of spokes in a
wheel occurs from pedaling torque and braking. Both of these are a couple of percent and of these
only braking has any significant effect, but only on the rim, not the spokes. Details of this are
explained in "the Bicycle Wheel".

I remember breaking a spoke doing a stoppie and coming back down on the rear wheel (the same 700x25)
with all my weight. I don't remember if it was at the 12 o clock or at 6 o clock position on the
wheel, but it definitely snapped when I came back down.

Is this the result of abnormally high forces? Or should this not have happened? Surely, if spoke
tension lessens at the contact patch, then it must increase elsewhere on the wheel. I should
probalby read your book, or another like it.

Quoted message said:

Quoted message said:

Jobst, what causes the indentations from the spokes that cross each other? Are they caused by
minute rubbing motions from road vibration? I ask because those replacement DT spokes had pretty
deep indentations in them when I got them and I'm wondering if they're to be a concern in the
long term.

Those divots are from fretting erosion and are minuscule with no effect on spoke failure. It can
probably occur, but in the years I have been around bicycle wheels, I have not seen a spoke fail
at the crossing. More important is that you should not reuse spokes once taken out of a wheel
because the elbow bends of the outbound spokes have been irrecoverably formed into an acute angle
that cannot be opened effectively by stress relieving. Therefore, these spokes will be prone to
elbow failures.

I'm under 150 lbs so I'm not too worried about it. The rim is shot and has hops in it all over so I
don't really care too much what happens to it.

Quoted message said:

Quoted message said:

It's great though because everything on the bum bike (Giant Kronos) was straight, even the
non-replaceable derailleur hangar. I slapped on new cables/housing/bars/saddle, and my $65 bike
is as good as the day it rolled out of the factory.

Which is probably not very good in comparison to better bicycles.

Well, that's true. It functions as my all-purpose race/beater/commuter/stupid stunts bike 😉 As long
as it shifts well and the wheels are true, I'm as happy as a clam.

--
Phil, Squid-in-Training

Squid-in-Training said:

I had bought it used from a bum.

Is it just me, or does that sound like code for "I bought a stolen bike from a junkie for the cost
of a hit of crack"?

Jasper

Squid-in-Training said:

And a bummy guy runs it. It's also not shady or secluded, so it can't be THAT illegal.

Dude, I get offered bikes by junkies that come with broken locks on them in broad daylight in a
fairly busy street. Shady and secluded isn't a particular requirement.

Jasper

Quoted message said:

More important is that you should not reuse spokes once taken out of a wheel because the elbow
bends of the outbound spokes have been irrecoverably formed into an acute angle that cannot be
opened effectively by stress relieving. Therefore, these spokes will be prone to elbow failures.

Anonynous (who?) writes:

Why would one try to "open the acute angle?" Why wouldn't one make them outbound in the next wheel
they go into?

Anonymous said:

Quoted message said:

More important is that you should not reuse spokes once taken out of a wheel because the elbow
bends of the outbound spokes have been irrecoverably formed into an acute angle that cannot be
opened effectively by stress relieving. Therefore, these spokes will be prone to elbow failures.

Quoted message said:

Why would one try to "open the acute angle?" Why wouldn't one make them outbound in the next wheel
they go into?

You would, but if you have tried it, you will know that assessing whether a spoke is inside or
outside looking at the bend, from a pile of used spokes, is a mess. With two lengths of spokes, left
and right spokes on a rear wheel, the angle is dependent on the dish.

So why (or what) are you hiding?

Jobst Brandt [email hidden] Palo Alto CA

Quoted message said:

Anonymous said:

Quoted message said:

More important is that you should not reuse spokes once taken out of a wheel because the elbow
bends of the outbound spokes have been irrecoverably formed into an acute angle that cannot be
opened effectively by stress relieving. Therefore, these spokes will be prone to elbow
failures.

Quoted message said:

Why would one try to "open the acute angle?" Why wouldn't one make them outbound in the next
wheel they go into?

You would, but if you have tried it, you will know that assessing whether a spoke is inside or
outside looking at the bend, from a pile of used spokes, is a mess.

I have tried it. I mark mine, so I know which are outbound/inbound X years later. I dot the head of
the outbounds with a "magic" marker before disassembly. I've not had a reused spoke break with this
technique. Then again, I don't weigh a great deal and have never had chronic problems with any bike
equipment. Spokes are expensive.