Anti-Seize or Grease??

Random-<< When building new components on a frame, is it best to use anti-seize or grease
on threads?

Either will work, Antisieze seems more tenacious-less likely to wash off..

<< Also, are there any special considerations for using Ti bolts in Alu threads?

Don't over torque and use antisieze. Or replace them with steel.

Peter Chisholm Vecchio's Bicicletteria 1833 Pearl St. Boulder, CO, 80302
(303)440-3535 vecchios.comvecchios.comOpen ↗ "Ruote convenzionali costruite eccezionalmente bene"

"RandomChris" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

When building new components on a frame, is it best to use anti-seize or grease on threads? I'd
heard that anti-seize is less likely to get washed away by water but it comes in such small tubes
(the finish line ti prep stuff) that I thought it must be for specific parts....

Also, are there any special considerations for using Ti bolts in Alu threads?

Titanium is extremely reactive when mated to another metal, urban myths about its being "inert"
notwithstanding. Use anti sieze paste, available at any auto parts store in lifetime-supply 300g
cans for $5~10. There are many brands with multiple features - any will do. (you don't care about
temperature range for bicycle aplication)

--
Andrew Muzi yellowjersey.orgyellowjersey.orgOpen ↗ Open every day since 1 April 1971

RandomChris said:

When building new components on a frame, is it best to use anti-seize or grease on threads? I'd
heard that anti-seize is less likely to get washed away by water but it comes in such small tubes
(the finish line ti prep stuff) that I thought it must be for specific parts....

Go to a good auto supply, a Volvo or Rover dealer and ask for copper grease ... it is the same thing
as anti-seize and cost about 1/100 of the price.

Quoted message said:

Also, are there any special considerations for using Ti bolts in Alu threads?

Al and Ti is a very important place to use copper grease.

"Qui si parla Campagnolo" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

<< Also, are there any special considerations for using Ti bolts in Alu threads?

Don't over torque and use antisieze. Or replace them with steel.

Yes, yes, and the last bit most important.

Robin Hubert

I was taught to use anti-seize for non-moving contacts like seatposts, any threads, headset parts
pressed into frame or onto fork crown, quill stems, etc. Grease is for moving contacts, i.e.
bearings. Never had a problem in 30 years. Large tin or plastic bottle of anti-seize, enough to last
for years of personal service on multiple bikes, is available at auto parts store for under $10.

RandomChris said:

When building new components on a frame, is it best to use anti-seize or grease on threads?

I use plumber's pipe dope.

I'm no engineer but I work in an industry that makes up a lot of threads, some over 100,000 ft/lbs.
Grease is a lubricant, it allows you to make up the threads eaiser. Anti seize has the grease or
carrier plus micro particles of some soft solid. The grease can wash out but these particles are
compressed between the threads. When you want to remove the bolt these compressed soft particles
shear (antiseize) and allow the part to screw out. They also help seal out water to prevent rust.
Rust cancels whatever you put on the threads. I like to used plumbers tape or teflon grease on my
bike. I have put the teflon paste on every metal to metal contact point on a crank to kill some
noise that another guy had suffered with for years. worked great. Make sure you have anti seize
under the head of the bolt as a lot of the torque is at this contact point rather then the threads.
Titanium is a problem material. Someone suggested that it is reactive, I don't know about that but
when it is cut rather then ground or polished it tends to leave microscopic wickers. These are like
putting sand in the treads before you make them up. They don't unscrew easy or not at all. Since
thay are jammed into the threads they tend to grip the threads so tight that when they are removed
they gall or mechanically weld (not a true weld) themselves together. This will pull the threads
right out of the materail they are cut into rather then unscrew. Like I said, I'm no engineer but
if you keep these things in mind when you make up threads you should have no problems on a bike.
One last thing get and use a torque wrench. It's easy to convince yourself you have the experience
to get the right torque on a bolt, but it's just as easy to pick up a torque wrench and do it
right. Chris

"RandomChris" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

When building new components on a frame, is it best to use anti-seize or grease on threads? I'd
heard that anti-seize is less likely to get washed away by water but it comes in such small tubes
(the finish line ti prep stuff) that I thought it must be for specific parts....

Also, are there any special considerations for using Ti bolts in Alu threads?

cheers Chris

Quoted message said:

<< Also, are there any special considerations for using Ti bolts in Alu threads?

Don't over torque and use antisieze. Or replace them with steel.

Speaking of which...

What is a good (beam) torque wrench for low torque fittings like handlebars clamps, mech hanger
bolts, etc? The Park ones seem a little pricey for what they are.

A Muzi <[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

"RandomChris" <[email hidden]> wrote in

message

Quoted message said:

"]news:[email hidden]...

Quoted message said:

When building new components on a frame, is it best to use anti-seize or grease on threads? I'd
heard that anti-seize is less likely to get

washed

Quoted message said:

Quoted message said:

away by water but it comes in such small tubes (the finish line ti prep stuff) that I thought it
must be for specific parts....

Also, are there any special considerations for using Ti bolts in Alu threads?

Titanium is extremely reactive when mated to another metal, urban myths about its being "inert"
notwithstanding. Use anti sieze paste, available

at

Quoted message said:

any auto parts store in lifetime-supply 300g cans for $5~10. There are

many

Quoted message said:

brands with multiple features - any will do. (you don't care about temperature range for bicycle
aplication)

Is Copper Slip the same stuff? Looks the same as the Ti anti-seize I have (dirty gold and pasty).

Would this go for any non-moving contact point, then? For example, I have a splined BB with a Ti
axle. The Park Tools website says you should normally grease a splined BB axle. Presumably this is
to stop the (usually steel) axle and (alu) crank seizing and nothing to do with seating it
correctly?

RandomChris said:

A Muzi <[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

"RandomChris" <[email hidden]> wrote in

message

Quoted message said:

"]news:[email hidden]...

Quoted message said:

When building new components on a frame, is it best to use anti-seize or grease on threads?
I'd heard that anti-seize is less likely to get

washed

Quoted message said:

Quoted message said:

away by water but it comes in such small tubes (the finish line ti prep stuff) that I thought
it must be for specific parts....

Also, are there any special considerations for using Ti bolts in Alu threads?

Titanium is extremely reactive when mated to another metal, urban myths about its being "inert"
notwithstanding. Use anti sieze paste, available

at

Quoted message said:

any auto parts store in lifetime-supply 300g cans for $5~10. There are

many

Quoted message said:

brands with multiple features - any will do. (you don't care about temperature range for bicycle
aplication)

Is Copper Slip the same stuff? Looks the same as the Ti anti-seize I have (dirty gold and pasty).

Would this go for any non-moving contact point, then? For example, I have a splined BB with a Ti
axle. The Park Tools website says you should normally grease a splined BB axle. Presumably this is
to stop the (usually steel) axle and (alu) crank seizing and nothing to do with seating it
correctly?

Antiseize will be fine for this. Personally I would use antiseize for that interface, but as a
practical matter, grease is likely to work just fine.

Quoted message said:

Quoted message said:

"RandomChris" <[email hidden]> wrote in

message

Quoted message said:

"]news:[email hidden]...

Quoted message said:

When building new components on a frame, is it best to use anti-seize

or

Quoted message said:

Quoted message said:

Quoted message said:

grease on threads? I'd heard that anti-seize is less likely to get

washed

Quoted message said:

Quoted message said:

away by water but it comes in such small tubes (the finish line ti

prep

Quoted message said:

Quoted message said:

Quoted message said:

stuff) that I thought it must be for specific parts....

Also, are there any special considerations for using Ti bolts in Alu threads?

Quoted message said:

A Muzi <[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

Titanium is extremely reactive when mated to another metal, urban myths about its being "inert"
notwithstanding. Use anti sieze paste,

available

Quoted message said:

at

Quoted message said:

any auto parts store in lifetime-supply 300g cans for $5~10. There are

many

Quoted message said:

brands with multiple features - any will do. (you don't care about temperature range for bicycle
aplication)

"RandomChris" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

Is Copper Slip the same stuff? Looks the same as the Ti anti-seize I have (dirty gold and pasty).

Would this go for any non-moving contact point, then? For example, I have

a

Quoted message said:

splined BB with a Ti axle. The Park Tools website says you should normally grease a splined BB
axle. Presumably this is to stop the (usually steel) axle and (alu) crank seizing and nothing to
do with seating it correctly?

I'm not big on any titanium spindle - - BB , pedals, all of them are unsafe IMHO.

but since you didn't ask me about that - if you've got one, yes use anti-seize.

I don't know the Copper Slip brand - does it say "anti-seize" on it? The usual anti-seize
application is for exhaust manifold bolts and exhaust systems - places where bolts corrode from
heat especially with dissimilar metals. Anything intended for that would be just fine here. Maybe
ask the vendor?
--
Andrew Muzi yellowjersey.orgyellowjersey.orgOpen ↗ Open every day since 1 April 1971

Try this link:

sandsmachine.comac greas.htmOpen ↗

S and S Machine makes torque couplings for frames so that they can be disassembled and fit into
airline size cases for air travel. They are adamant about using Dupont pure Teflon grease on the
threads to avoid seizing, and give their test results in the above URL and the linked pages to prove
their case.

RandomChris said:

When building new components on a frame, is it best to use anti-seize or grease on threads? I'd
heard that anti-seize is less likely to get washed away by water but it comes in such small tubes
(the finish line ti prep stuff) that I thought it must be for specific parts....

Also, are there any special considerations for using Ti bolts in Alu threads?

cheers Chris

--
Cheers! OliverS When replying personally, remove "_removespam_"

"When I see an adult on a bicycle, I do not despair for the future of the human race." HG Wells

I use food grade anti seize. Probably doesn't work any different from the other stuff, but neater
and no metal in it. Left over from my last job. It was pretty cheap, but I don't remember exactly
where it came from. My first guess was McMaster-Carr, but they only sell to companies.

ajames54 said:

RandomChris said:

When building new components on a frame, is it best to use anti-seize or grease on threads? I'd
heard that anti-seize is less likely to get washed away by water but it comes in such small tubes
(the finish line ti prep stuff) that I thought it must be for specific parts....

Go to a good auto supply, a Volvo or Rover dealer and ask for copper grease ... it is the same
thing as anti-seize and cost about 1/100 of the price.

Quoted message said:

Also, are there any special considerations for using Ti bolts in Alu threads?

Al and Ti is a very important place to use copper grease.

--
Lincoln Ross NOTE ADDRESS CHANGE: [email hidden]

For esoteric anti seize compounds you might want to try the following two companies: either GRAINGER or BROWNELLS. The latter is America's pre-eminent gunsmithing supply firm. (And please don't give me **** posting the latter.)

Otherwise, contact a local machine shop who may be able to best advise you on your application.

As to TORQUE WRENCHES, Snap-On Tools sells probably the most expensive ones. You're dollars and headaches ahead by purchasing one from them . And it had better be the micrometer style as opposed to the cheap pointer one. And I mean it.