Am I hard enough for single speed??

<[email hidden]> wrote in message
news:[email hidden]...

Quoted message said:

Any comments or arguments for/against?

Fixed - YKIMS :-)

cheers,
clive

Quoted message said:

Any comments or arguments for/against?

I normally commute on a rohloff-equipped steel touring bike, with
panniers and pulling 50kg of trailer, my hilly route means the 1st gear
is used a lot. Going to fixed (for non-school-run commutes), I choose
a 2:1 ratio, but already I'm going to go higher: "I think I can--I
think I can". So I guess thats a vote for fixed: the lightness of the
fixie makes it hugely easier to ride uphill with gear ratios that just
wouldn't hack it with a fully-equipped bike.

Quoted message said:

Hi all

For my daily commute a nexus equipped steed which is coming to the end
of its useful life (+10000 miles). Since I do not have the funds to go
rohloff I wondered about turning courier and moving to single speed
(specialized langster please), but am wondering how much harder my
commute would be?
I have already geared my nexus down to a 17t and find that I only
really use gears 4-8 in normal operation, so I may be able to get away
with it. I have a couple of largish hills on my home journey but they
are long rather than steep.

Any comments or arguments for/against?

Cheers

Steve

Do you mean single speed or fixed ? Only you can decide if you are hard
enough, can't see why not if you choose its gear sensibly. Its not all
or nothing, you can change the ratios relatively easily. Single speed
is easier than fixed as you can freewheel down the hills. Like the
other bloke says, with a shorter chain, 1 chain ring, 1 sprocket, no
mechs a fixed is going to be lighter than a geared bike.

Quoted message said:

Any comments or arguments for/against?

Find out how hard it is empirically: select a single speed on your hub
and don't change out of it for the journey. If it's too hard, try the
next one down the next day. And so on.

If one of them works out okay then the next question is are you hard
enough for a fixed gear, which has even less maintenance and slightly
better efficiency. Don't apply if you enjoy freewheeling!

Singlespeed/fixie makes a lot of sense if you can cut it because it's
lighter and there's less to go wrong and wear out: Darth Ben "Kinetics"
Cooper, who not only /can/ afford Rohloffs but has several in the bike
shop he owns, commutes on a single speed bike.

Pete.
--
Peter Clinch Medical Physics IT Officer
Tel 44 1382 660111 ext. 33637 Univ. of Dundee, Ninewells Hospital
Fax 44 1382 640177 Dundee DD1 9SY Scotland UK
net [email hidden] http://www.dundee.ac.uk/~pjclinch/

sothach said:

Quoted message said:

Any comments or arguments for/against?

I normally commute on a rohloff-equipped steel touring bike, with
panniers and pulling 50kg of trailer, my hilly route means the 1st
gear is used a lot. Going to fixed (for non-school-run commutes), I
choose a 2:1 ratio, but already I'm going to go higher: "I think I
can--I think I can". So I guess thats a vote for fixed: the
lightness of the fixie makes it hugely easier to ride uphill with
gear ratios that just wouldn't hack it with a fully-equipped bike.

50kg of trailer had me seriously impressed until I read the school run bit.
Still impressive, less confusing, though.

--
Ambrose

Cheers for the replies guys.
I will def go for single speed freewheel and not fixed (so don't try
and talk me out of it). I guess I'll try the single gear approach as a
quick test, and if I find a gear that's comfortable for the commute I
could find the appropriate ratio for a proper single set-up?

I like my Nemesis for its total lack of maintenance (nexus gear plus
roller brakes) but the gears are not up to distance riding. If I went
to a specialized langster I would have to put up with side-pull brakes
though : (

Quoted message said:

I like my Nemesis for its total lack of maintenance (nexus gear plus
roller brakes) but the gears are not up to distance riding. If I went
to a specialized langster I would have to put up with side-pull brakes
though : (

Go for a pompino and get cantilevers instead, also lots of clearance for
mudguards.

http://tinyurl.com/qenju

--
Andy Morris

AndyAtJinkasDotFreeserve.Co.UK

Love this:
Put an end to Outlook Express's messy quotes
http://home.in.tum.de/~jain/software/oe-quotefix/

--
Posted via NewsDemon.com - Premium Uncensored Newsgroup Service
------->>>>>>http://www.NewsDemon.com<<<<<<------
Unlimited Access, Anonymous Accounts, Uncensored Broadband Access

Quoted message said:

Cheers for the replies guys.
I will def go for single speed freewheel and not fixed (so don't try
and talk me out of it).

No intention to talk you out of it, but when I stripped the threads on
my cheapo hub/sprocket, I flipped to the flop side and used the
freewheel. It felt total carp after the fixed gear, sort of not one
thing or the other: at least build with a flip-flop hub and then you
can be a *double* hard [censored].

In message <[email hidden]>,
[email hidden] writes

Quoted message said:

Cheers for the replies guys.
I will def go for single speed freewheel and not fixed (so don't try
and talk me out of it). I guess I'll try the single gear approach as a
quick test, and if I find a gear that's comfortable for the commute I
could find the appropriate ratio for a proper single set-up?

I like my Nemesis for its total lack of maintenance (nexus gear plus
roller brakes) but the gears are not up to distance riding. If I went
to a specialized langster I would have to put up with side-pull brakes
though : (

My tuppence worth being that I recently got me a fixed wheel at the
grand old age of 5*. I live up a hill and whilst its a grind going up,
the efficiency and lightness of the bike largely compensate. I have
however chosen a fairly small gear of about 66". This tops out at 30mph
going downhill but by heck your legs are spinning.

If I am hard enough I guess you should be too.

Cheers
--
Bob Downie
Downie GeoScience Ltd.
please remove #n0spam# to reply directly

I forgot about the weight difference 'twixt bikes.
My current steed tops out at 30lb and the Langster is only 20.5lb!!
Should make a difference in climbing ability i guess.

Tested 2 commutes in a single gear (6th out of 8) and found it easy, to
my surprise. Will try 7th for the rest of the week but this could be a
step too far.

My only concern is the slight lack of speed I had when I approached a
major roundabout, which I would normally hit at 30+. This makes for
easy entry onto the roundabout and I don't hold traffic up, but I would
be a bit slower on a single I think - it may be nothing to worry about..

Well I have successfully tested single speed riding enough to convince
myself I'm having a SS bike. Problem now comes in that I have just
used Sheldon Brown's gear calculator and am not sure about the
outcome!

Using his figures for 26 X 1.25 / 32-559 / MTB tire with 175 mm cranks
and 46/18 in 7th gear (what I have settled on) I get a gear inch of
88.7

Using the figures for the Langster I'm buying For 700 X 23 / 23-622
tire with 170 mm cranks and 48/16 I get a gear inch 78.8

If I drop the rear sprocket on the langster to a 14 I could get 90.4

Do these figures still seem too high? I was expecting to see 65 -
70" but I don't know what an average or good inch'age(!) would
be?

Cheers

Steve

In article <[email hidden]>,

() said:

Using the figures for the Langster I'm buying For 700 X 23 / 23-622
tire with 170 mm cranks and 48/16 I get a gear inch 78.8

If I drop the rear sprocket on the langster to a 14 I could get 90.4

Do these figures still seem too high? I was expecting to see 65 -
70" but I don't know what an average or good inch'age(!) would
be?

Recent discussion of this on ACF:

<URL:http://bikereader.com/forum/index.php?topic=13598.0>

Personally I use 44-18, but that's a fair bit lower than most people
(and a LOT lower than Steve Abraham).

--
Dave Larrington - <http://www.legslarry.beerdrinkers.co.uk/>
Life - loathe it or ignore it, you can't like it.

Quoted message said:

Well I have successfully tested single speed riding enough to convince
myself I'm having a SS bike. Problem now comes in that I have just
used Sheldon Brown's gear calculator and am not sure about the
outcome!

Using his figures for 26 X 1.25 / 32-559 / MTB tire with 175 mm cranks
and 46/18 in 7th gear (what I have settled on) I get a gear inch of
88.7

I think there is a mistake here. I would guestimate this as ~66 inches.
I never bother to include the crank size in any calculations of gear
inches, as the meaning of it goes back to how many inches the wheel on
your penny farthing was, and changing the crank length would not change
the size of the wheel. If you express gearing as a leverage factor, then
crank length does come into it.

Quoted message said:

Using the figures for the Langster I'm buying For 700 X 23 / 23-622
tire with 170 mm cranks and 48/16 I get a gear inch 78.8

If I drop the rear sprocket on the langster to a 14 I could get 90.4

Do these figures still seem too high? I was expecting to see 65 -
70" but I don't know what an average or good inch'age(!) would
be?

90 seems a bit high unless your journey is indoors on a wooden surface.
I would recommend you try what is on the Langster (nice) before making
any decisions. I think the langster is higher geared than the gear you
have worked out is the one you like.

JimP

--
Let's think the unthinkable, let's do the undoable, let's prepare to
grapple with the ineffable itself, and see if we may not eff it after
all. - DNA

Quoted message said:

Well I have successfully tested single speed riding enough to convince
myself I'm having a SS bike. Problem now comes in that I have just
used Sheldon Brown's gear calculator and am not sure about the
outcome!

Using his figures for 26 X 1.25 / 32-559 / MTB tire with 175 mm cranks
and 46/18 in 7th gear (what I have settled on) I get a gear inch of
88.7

Using the figures for the Langster I'm buying For 700 X 23 / 23-622
tire with 170 mm cranks and 48/16 I get a gear inch 78.8

If I drop the rear sprocket on the langster to a 14 I could get 90.4

Do these figures still seem too high? I was expecting to see 65 -
70" but I don't know what an average or good inch'age(!) would
be?

Cheers

Steve

If you can do your routes on 90" then why not ? My fixed is 61", low by
some standards but high enough for me atm. Why not spin around on 48x16
and see how you like it, change it if its too low, it'll cost less than
£20 for a new sprocket and chain.

Quoted message said:

Well I have successfully tested single speed riding enough to convince
myself I'm having a SS bike. Problem now comes in that I have just
used Sheldon Brown's gear calculator and am not sure about the
outcome!

Using his figures for 26 X 1.25 / 32-559 / MTB tire with 175 mm cranks
and 46/18 in 7th gear (what I have settled on) I get a gear inch of
88.7

I suspect a typing error when using Sheldon's calculator. I've just tried
to replicate your figure, and come out with a 62.5in result, much closer to
the values otehrs in the thread estimated.

Quoted message said:

Using the figures for the Langster I'm buying For 700 X 23 / 23-622
tire with 170 mm cranks and 48/16 I get a gear inch 78.8

That's what I make it.

- Nigel

--
Nigel Cliffe,
Webmaster at http://www.2mm.org.uk/