42mm bearings to 40mm

not easily. supposedly jagur has some that will fit, and i think he got
them from torker, but i don't remember.

--
markf

stuck in iowa and gainfully employed.
------------------------------------------------------------------------
markf's Profile: http://www.unicyclist.com/profile/8102
View this thread: http://www.unicyclist.com/thread/46874

You need Torker DX bearings. You're LBS can get them.

--
pdc

"What doesn't kill you strengthens you, what kills you strengthens your
mother"
------------------------------------------------------------------------
pdc's Profile: http://www.unicyclist.com/profile/8160
View this thread: http://www.unicyclist.com/thread/46874

i dont under stand

i have an lx and want to get a qu-ax hub, so could i just take the lx
bearings off and put them on the qu-ax hub

--
unijesse

I Brake for Unicyclist's
http://www.nickjantz.2ya.com
------------------------------------------------------------------------
unijesse's Profile: http://www.unicyclist.com/profile/10868
View this thread: http://www.unicyclist.com/thread/46874

No, that I'm sure of. The LX bearing's inside diameter is smaller than
the Qu-Ax hub, I'm positive the LX bearings wouldn't make it.

--
forrestunifreak

I do not believe in computer programers.
'My gallery' (http://tinyurl.com/bbf9x)

"If I am ever that good I will be in a constant state of crapping my
pants." ~ koebwil
------------------------------------------------------------------------
forrestunifreak's Profile: http://www.unicyclist.com/profile/6828
View this thread: http://www.unicyclist.com/thread/46874

so then i could use dx bearings?

--
unijesse

I Brake for Unicyclist's
http://www.nickjantz.2ya.com
------------------------------------------------------------------------
unijesse's Profile: http://www.unicyclist.com/profile/10868
View this thread: http://www.unicyclist.com/thread/46874

unijesse said:

so then i could use dx bearings?

Yes!

--
forget_your_life

dream one dream many....
*'R.I.P' (http://tinyurl.com/vr86)*
------------------------------------------------------------------------
forget_your_life's Profile: http://www.unicyclist.com/profile/4558
View this thread: http://www.unicyclist.com/thread/46874

Is it possible to put the 42mm bearings into the 40mm holders? I was
able to do that on my Nimbus II, with no problems, though I HAVE heard
that other people have had problems. Or is the problem that the
current setup is using 42mm and you want to start using 40mm?

--
evil-nick

Fear is the mind-killer. Fear is the little-death that brings total
obliteration. I will face my fear. I will permit it to pass over me and
through me. And when it has gone past, I will turn the inner eye to see
its path. Where the fear has gone there will be nothing. Only I will
remain.

* Bene Gesserit Litany Against Fear.

I'm late for checkers with the Dalai Lama!

My gallery:
http://evil.linuxfreak.ca/uni.html
Our Club:
http://cs.ubishops.ca/~buuc/
------------------------------------------------------------------------
evil-nick's Profile: http://www.unicyclist.com/profile/6692
View this thread: http://www.unicyclist.com/thread/46874

evil-nick said:

Is it possible to put the 42mm bearings into the 40mm holders?

somtimes it is possible but in this case its not the outside diameter we
are talking about....its the inner diameter.

so once again for the record:

LX 17mm inner 40mm outer <--- found easily

DX 20mm inner 40 outer. <---found only though Torker USA

--
forget_your_life

dream one dream many....
*'R.I.P' (http://tinyurl.com/vr86)*
------------------------------------------------------------------------
forget_your_life's Profile: http://www.unicyclist.com/profile/4558
View this thread: http://www.unicyclist.com/thread/46874

if Im right bedford has the bearing you need..

--
maxisback

Quiters never win, winners never quit , the ones who never win and never
quit are just dumb
------------------------------------------------------------------------
maxisback's Profile: http://www.unicyclist.com/profile/10885
View this thread: http://www.unicyclist.com/thread/46874