26/20 -) 26/26 conversion?

My last homebuilt (stratus clone -long wheel-base) ended up with 700/700 wheels ,which really rolls
easily and handles well.I'm happy with it. Potential problems with your conversion are pedal
clearance ,and wheel flop, depending on your fork. By adding trail(bending) to my 700 forks to get
rid of flop,I solved the clearance problem at the same time(myBB is lower than your R40). Shorter
cranks can also help with clearance. "Markku Poysti" <[email hidden]_nospam> wrote in message
"]news:[email hidden]...

Quoted message said:

Has anybody tried to convert 26/20 recumbent into 26/26?

Just tried putting about 7 cm of books under front wheel of my Vision R40 (LWB/USS), and noticed
that my feet still reach the ground well enough. It should be rather easy to find cheap used MTB
steel front fork and weld the small part needed for steering linkage.

If that works, i get bottom bracket a few cm higher than seat, which i hope is better than the
current 0 cm.

It would be almost like the Vision "Saber", but in LWB.

Also i don't have to deal with the 406 size problems. Studded tires easily available + good
selection of summer tires.

Also i hope that curbs, rocks and loose snow will be less of a problem.

[email hidden]_nospam (Markku Poysti) wrote in message news:<[email hidden]>...

Quoted message said:

Has anybody tried to convert 26/20 recumbent into 26/26? Just tried putting about 7 cm of books
under front wheel of my Vision R40 (LWB/USS), and noticed that my feet still reach the ground well
enough. It should be rather easy to find cheap used MTB steel front fork and weld the small part
needed for steering linkage.

[snip]

If you are intending to swap the 20" (406) front wheel to a 26" (559) you will raise the front end
of your R40 by aprox 15cm. Judging by the photo on the website
(visionrecumbents.comBikeBigR40EUMed.jpgOpen ↗) this would raise your seat height by
aprox 11cm.

Quoted message said:

If you are intending to swap the 20" (406) front wheel to a 26" (559) you will raise the front end
of your R40 by aprox 15cm.

Good point. But even with 15 cm under the front wheel, i could reach the ground with my feet.
(I'm 170 cm)

[email hidden] (David) wrote in message
news:<[email hidden]>...

Quoted message said:

[email hidden]_nospam (Markku Poysti) wrote in message news:<[email hidden]>...

Quoted message said:

Has anybody tried to convert 26/20 recumbent into 26/26? Just tried putting about 7 cm of books
under front wheel of my Vision R40 (LWB/USS), and noticed that my feet still reach the ground
well enough. It should be rather easy to find cheap used MTB steel front fork and weld the small
part needed for steering linkage.

[snip]

If you are intending to swap the 20" (406) front wheel to a 26" (559) you will raise the front end
of your R40 by aprox 15cm. Judging by the photo on the website
(visionrecumbents.comBikeBigR40EUMed.jpgOpen ↗) this would raise your seat height by
aprox 11cm.

doh...not 11cm...only 5cm seat raise..it was a long day 🙁

If a 26" front wheel replaces a 20" wheel, the front of the bike will be raised only 3" (or about
7.5 cm) - not six inches. Accordingly, the seat itself would be raised only about 1 inch to 1.5
inches, depending on the bike geometry.

hepso.dna.fi2626.jpgOpen ↗

Here is a picture of the 26/26 modified Vision.

No clearance problems.

There is some wheel flop, but i don't think it is a problem.

Nice job!

I just posted the same question about a week ago on BROL and received no responses.

I sent an email to Vision asking the same question and they warned me to not make the conversion.
This made me want to do it even more.

Then I saw your post and the responses.

I want to convert a SWB R40 to 26/26. I need to find an R40 first though. I have a Rocket and want
at least a 26 inch rear wheel. The Rocket wheels can't be changed to anything that I know of.

Markku Poysti <[email hidden]_nospam> wrote in message "]news:[email hidden]...

Quoted message said:

hepso.dna.fi2626.jpgOpen ↗

Here is a picture of the 26/26 modified Vision.

No clearance problems.

There is some wheel flop, but i don't think it is a problem.

M.T. Flaman said:

If a 26" front wheel replaces a 20" wheel, the front of the bike will be raised only 3" (or about
7.5 cm) - not six inches.

That's assuming you can use the same fork, which seems unlikely. If you use a longer fork to
accomodate the larger wheel, the front will raised by 6".

Ken Kobayashi [email hidden] solarwww.mtk.nao.ac.jppersonalOpen ↗

I converted a Speed Ross using a carbon fiber 650 fork and a 26" wheel. Biggest problem was
reworking the brake to avoid conflict with the frame. Bike rides better than before.

Pete Huber Speed Ross Pulaski, VA

"Markku Poysti" <[email hidden]_nospam> wrote in message "]news:[email hidden]...

Quoted message said:

Has anybody tried to convert 26/20 recumbent into 26/26?

Just tried putting about 7 cm of books under front wheel of my Vision R40 (LWB/USS), and noticed
that my feet still reach the ground well enough. It should be rather easy to find cheap used MTB
steel front fork and weld the small part needed for steering linkage.

If that works, i get bottom bracket a few cm higher than seat, which i hope is better than the
current 0 cm.

It would be almost like the Vision "Saber", but in LWB.

Also i don't have to deal with the 406 size problems. Studded tires easily available + good
selection of summer tires.

Also i hope that curbs, rocks and loose snow will be less of a problem.

Great idea Markuu. You'll be faster, smoother, and more aerodynamic.

Ken Kobayashi said:

That's assuming you can use the same fork, which seems unlikely. If you use a longer fork to

accomodate the larger wheel, the front will raised by 6".

Ken/David are pretty close with their numbers, although the head tube angle and fork rake will combine to reduce these numbers a little.

Be aware that your head tube angle will slacken quite a bit with the new larger fork/wheel. Depending on the handling characteristics of your current setup, you should determine your necessary fork rake appropriately, as your trail will be increasing substantially.

Like Obento says, trail will be so great that "wheel flop" will become a problem. :eek:

You may end up changing (rewelding) the angle of your head tube to compensate.

Have fun with the project!
R2

"Robert Riggins" <[email hidden]> wrote in message

Quoted message said:

I want to convert a SWB R40 to 26/26. I need to find an R40 first though. I have a Rocket and want
at least a 26 inch rear wheel. The Rocket wheels can't be changed to anything that I know of.

I'm not sure if this applies to all Rockets, but the newer ones, with the 2" main tube are easily
converted to 26" rear wheel.

There was a thread here a few months ago about doing so on a Tailwind, which uses the same rear
stays. I believe all they had to do was move the bridge between the lower stays. I think they
mounted a sidepull on the bridge, but it wouldn't be hard to add new canti pivots.

If you're up to a little frame hacking, it wouldn't be hard to make a
26/20 Rocket that didn't raise the seat.

I unfortunately have the 2000 model and have tried a 559. It's not even close. The rear end of the
main tube is the limiter. I would need longer stays. That becomes a bit more work than I want.

Thanks, Rob

Mark Stonich <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

"Robert Riggins" <[email hidden]> wrote in message

Quoted message said:

I want to convert a SWB R40 to 26/26. I need to find an R40 first

though. I

Quoted message said:

Quoted message said:

have a Rocket and want at least a 26 inch rear wheel. The Rocket wheels can't be changed to
anything that I know of.

I'm not sure if this applies to all Rockets, but the newer ones, with the 2" main tube are easily
converted to 26" rear wheel.

There was a thread here a few months ago about doing so on a Tailwind, which uses the same rear
stays. I believe all they had to do was move the bridge between the lower stays. I think they
mounted a sidepull on the bridge, but it wouldn't be hard to add new canti pivots.

If you're up to a little frame hacking, it wouldn't be hard to make a
26/20 Rocket that didn't raise the seat.

R2D2 said:

Ken Kobayashi said:

That's assuming you can use the same fork, which seems unlikely. If you use a longer fork to

accomodate the larger wheel, the front will raised by 6".

Ken/David are pretty close with their numbers, although the head tube angle and fork rake will
combine to reduce these numbers a little.

The 6" figure was a first-order approximation. ;-) Actual number would depend on the forks.

Quoted message said:

Like Obento says, trail will be so great that "wheel flop" will become a problem. :eek: You may end
up changing (rewelding) the angle of your head tube to compensate.

Wouldn't it be easier to re-weld the fork to increase the rake? I wonder if you could just bend
the fork...

Ken Kobayashi [email hidden] solarwww.mtk.nao.ac.jppersonalOpen ↗

Ken said:

Wouldn't it be easier to re-weld the fork to increase the rake? I wonder if you could just bend the fork...

You are right-on Ken. (And I didn't do the geometry either, but your 6 inches was Very close 🙂 )

Bending the fork to increase the rake would be a given, as Obento mentioned. However there is a good chance that the increase may not be enough, and changing the head tube angle may be necessary. It all depends on how it steers once put back together.

Hmm, I wonder if using a 700c or 27" fork would give you enough real estate... You may not even have to reweld the brake bosses when done.

Just a thought. I've never actually done a conversion, but have welded them from the ground up.