Bicycle Bad Welds Problem

Quoted post said:

Originally posted by jeboyt
2-10-2004

Attention Member Bicycle Shop Owners,

Subject: Bad Welds Investigation

After receiving a large number of complaints of defective bicycles, several involved in road
accidents, we launched an investigation six months ago into the cause of bicycle failure and
instability at high speeds.

Our investigation has found defective welds of steel tubes from several different bicycle
manufactures that are made overseas. This is apparently caused by use of low cost and contaminated
welding rods. The welds are corrosive, therefore internally rust and weaken quickly.

Please inspect each weld for any signs of rusting or small cracks. If one deviation is found, the
bicycle may be re-welded at that joint. If two or more deviations are found, the bicycle should be
considered unsafe to ride, and the owner notified.

The rods are manufactured in China, and are currently being sold to many bicycle frame manufactures
in the Far East, including Japan, China, Taiwan, Malaysia, and others.

There have been no reports of American made bicycles having this defect.

We have notified the manufactures involved of the quality problems.

Thank you,

Henry Fisher, President

American Bicycle Retail Association

#3241 Forth Floor
1212 North Palmer Street Washington, D.C

Dear Jeboyt,

Are you sure that you're not on 1234 Thurd Floor?

Carl Fogel

<[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

2-10-2004

Attention Member Bicycle Shop Owners,

Subject: Bad Welds Investigation

<<snip..>>

Quoted message said:

Henry Fisher, President

What a load of road apples..I think it's actually Henry "The Troll" Fisherman....nice try. You can't
beat the helmet thread!!

carlfogel said:

Quoted message said:

Henry Fisher, President American Bicycle Retail Association

Hmm. I can't find any information about this group on the net. Anyone? Or is he just spreading
rumors to discredit cheap bikes (as if that needs any help)?

Quoted message said:

There have been no reports of American made bicycles having this defect.

Of course, since he is apparently talking about cheap bicycle-shaped toys, I don't think there are
any American-made comparable bicycles to compare to.

--

David L. Johnson

__o | As far as the laws of mathematics refer to reality, they are not _`\(,_ | certain, and as
far as they are certain, they do not refer to (_)/ (_) | reality. -- Albert Einstein

"David L. Johnson" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

Hmm. I can't find any information about this group on the net. Anyone? Or is he just spreading
rumors to discredit cheap bikes (as if that needs any help)?

Nah, it's a heap of steaming [censored]. I noticed he used an anonymous remailer..

Cheers,

Scott..

Quoted message said:

Henry Fisher, President

American Bicycle Retail Association

#3241 Forth Floor
1212 North Palmer Street Washington, D.C

With a hotmail address? ([email hidden])

--Mike-- Chain Reaction Bicycles chainreactionbicycles.comchainreactionbicycles.comOpen ↗

may have said:

Henry Fisher, President

American Bicycle Retail Association

#3241 Forth Floor
1212 North Palmer Street Washington, D.C

No record of that organization was found.

USPS says "no such address"

"Fourth" is misspelled.

Trollishness: Very high.

My opinion: Bogon flux overload alert!

--
My email address is antispammed; pull WEEDS if replying via e-mail.
Yes, I have a killfile. If I don't respond to something,
it's also possible that I'm busy.
Words processed in a facility that contains nuts.

Quoted message said:

2-10-2004 Attention Member Bicycle Shop Owners, Subject: Bad Welds Investigation

{Pile o' crappage snipped}

Quoted message said:

Henry Fisher, President American Bicycle Retail Association
#3241 Forth Floor
1212 North Palmer Street Washington, D.C

{cough-cough} [censored] {cough-cough}

Bill "go fourth (heh) and make up a real address (DC has directionals AND ZIPs)" S.

<[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

2-10-2004

Attention Member Bicycle Shop Owners,

Subject: Bad Welds Investigation

After receiving a large number of complaints of defective bicycles, several involved in road
accidents, we launched an investigation six months ago into the cause of bicycle failure and
instability at high speeds.

Our investigation has found defective welds of steel tubes from several different bicycle
manufactures that are made overseas. This is apparently caused by use of low cost and contaminated
welding rods. The welds are corrosive, therefore internally rust and weaken quickly.

Please inspect each weld for any signs of rusting or small cracks. If one deviation is found, the
bicycle may be re-welded at that joint. If two or more deviations are found, the bicycle should be
considered unsafe to ride, and the owner notified.

The rods are manufactured in China, and are currently being sold to many bicycle frame
manufactures in the Far East, including Japan, China, Taiwan, Malaysia, and others.

There have been no reports of American made bicycles having this defect.

We have notified the manufactures involved of the quality problems.

Oh, excellent! Just excellent. Nothing like some good humor to begin one's Friday!

Quoted message said:

Thank you,

Thank YOU,

Dave

Quoted message said:

Henry Fisher, President

American Bicycle Retail Association

#3241 Forth Floor
1212 North Palmer Street Washington, D.C

3241 Forht Fl. HAAAA-ha-ha-ha... HAAAA-ha-ha... Ahhhhhhhhh.... That's funny.