Koxx One ISIS hub width?

I don't know how far apart they are but I do know they fit in a yuni
frame, so if you can find out how wide a hub a yuni will accept you can
find out.

--
ntappin
------------------------------------------------------------------------
ntappin's Profile: http://www.unicyclist.com/profile/10800
View this thread: http://www.unicyclist.com/thread/48143

since "all" are 100 c-c it should be just that.
if not, you could rearange the spacers!

--
lleberg

I <3 my unicycle!
------------------------------------------------------------------------
lleberg's Profile: http://www.unicyclist.com/profile/8272
View this thread: http://www.unicyclist.com/thread/48143

'Splined Unicycle Hub Comparator'
(http://www.unicycle.uk.com/hubcomparator.html)

--
saam

Ronnie said:

"Crippled but still keen, I salute you!"

my dream stock unicycle:'koxx' (http://tinyurl.com/do9yc)
my dream custom unicycle:'kh '
(http://www.unicyclist.com/forums/showthread.php?t=46723)
------------------------------------------------------------------------
saam's Profile: http://www.unicyclist.com/profile/9168
View this thread: http://www.unicyclist.com/thread/48143

lleberg said:

since "all" are 100 c-c it should be just that.

is it 100mm between the bearings or from bearing axle to bearing axle?
(how much space left between bearings?)
other question: could we get rid of the flanges (and the envelope that
supports the flange) ; keep the naked axle and provide our own
envelope+flanges ?
(by "envelope" -I do not know the exact term- I mean for instance the
coloured part of QU-ax axles)
thanks

--
wobbling bear

One Wheel : bear necessity
------------------------------------------------------------------------
wobbling bear's Profile: http://www.unicyclist.com/profile/3716
View this thread: http://www.unicyclist.com/thread/48143

Thanks for the info. I realized another problem though. My frame uses
40mm bearings and the Koxx One uses 42mm. Are there 40mm bearings that
will fit the Koxx One hub? The Kozz One hub is the only one I'm really
considering now because of the shorter cranks available, and I'd rather
not have to buy a new frame as well. Hopefully something will work
out.
Thanks,
Andrew

--
andrew361
------------------------------------------------------------------------
andrew361's Profile: http://www.unicyclist.com/profile/10444
View this thread: http://www.unicyclist.com/thread/48143

What frame do you have?

Onza uses the 40mm OD nimbus II frame for the kh/onza 42mm OD bearings,
as they aren't too tight.. it isnt a problem.

--
lleberg

I <3 my unicycle!
------------------------------------------------------------------------
lleberg's Profile: http://www.unicyclist.com/profile/8272
View this thread: http://www.unicyclist.com/thread/48143

http://www.unicycle.com/shopping/shopexd.asp?id=610

I have this frame but I still use the stock koxx, splined hub.

--
ntappin
------------------------------------------------------------------------
ntappin's Profile: http://www.unicyclist.com/profile/10800
View this thread: http://www.unicyclist.com/thread/48143

wobbling bear said:

is it 100mm between the bearings or from bearing axle to bearing axle?
(how much space left between bearings?)
other question: could we get rid of the flanges (and the envelope that
supports the flange) ; keep the naked axle and provide our own
envelope+flanges ?
(by "envelope" -I do not know the exact term- I mean for instance the
coloured part of QU-ax axles)
thanks

The 100mm is from the centre of one bearing to the centre of the other.
I believe with the Koxx the centre part of the hub and the flanges are
welded on, so they cannot be pressed off like on Kh and Onza hubs, so
no i don't think you could use the axle and make your own hub, unless
they'll sell you just the axle as a one-off.

--
kington99

Dave

- what a thoroughly post-modern subversion of the cycling genre -
------------------------------------------------------------------------
kington99's Profile: http://www.unicyclist.com/profile/9417
View this thread: http://www.unicyclist.com/thread/48143

I'm using a Nimbus X frame. I'm not sure, but for some reason I think my
Dad's uni uses 42mm bearings. Maybe I'll go over and borrow it to see
how it fits. Thanks for the help.
Andrew

--
andrew361
------------------------------------------------------------------------
andrew361's Profile: http://www.unicyclist.com/profile/10444
View this thread: http://www.unicyclist.com/thread/48143

Another question regarding width- how does the Q-factor compare with the
KH/Onza?

Is it compatible with the KH frame?

--
GizmoDuck

'www.adventureunicyclist.com' (http://www.adventureunicyclist.com/)
'Laos Unicycle Tour' (http://www.laosunitour.org)
'New Zealand Unicycle Federation' (http://www.unicycle.org.nz)

The SINZ Unitour- coming soon......
------------------------------------------------------------------------
GizmoDuck's Profile: http://www.unicyclist.com/profile/794
View this thread: http://www.unicyclist.com/thread/48143

The Koxx ISIS cranks are dead straight (perpendicular to the axis of the
axle), they have no Q angle and thus vary from the KH/ONza cranks,
which have quite a lot. I have seen a KOxx hub in a KH 24 '05 frame
working fine, so yes they are compatible.

--
kington99

Dave

- what a thoroughly post-modern subversion of the cycling genre -
------------------------------------------------------------------------
kington99's Profile: http://www.unicyclist.com/profile/9417
View this thread: http://www.unicyclist.com/thread/48143