UK and Europe · Public discussion

upgrading an old Dawes Galaxy - help needed !!

Started by Pete A · · Last activity · 3 posts · 1,242 views

Thread details

What we know about this thread

Original section
UK and Europe
Published
17 December 2004
Last activity
19 December 2004
Original author
Pete A
Posts
3
Discussion status
Public discussion
Total views
1,242
Views / 30 days
0

The navigation and discussion metadata provide context. Posts remain in their original chronological order.

Showing posts 1–3 of 3
Posts remain in their original chronological order.

Text size
  1. Thanks for all the comments. Yes, will take bike back to LBS & get
    them to check out the front mech. Have about managed to get it
    working, with only a slight touching on inside face when in lowest
    gear. However, the height is [censored] postion - nearly 6mm above outer
    ring ! The front mech is a 'Nexave Compact' one, so I would have
    thought that this is suitable for any compact chainset ?? Ideally, I
    need to front mech cage to be about 3 or 4 mm shorter, then it would
    clear frame ok.

    Cant understand if others have upgraded bikes of this era, why this
    particular Galaxy has such a bad chainline ? I assume it would have
    originally been a 10 speed setup, as this bike has chromed front forks
    - think it must be early 1980's model. The person I bought it off had
    it setup as a single speed bike, so dont know if this would have made
    a difference.

    Does anyone know of likely costs in future if I was looking at having
    it stripped down, relevant cantilever/bottle bosses put on & resprayed
    ? The frame is basically sound, though its showing its age ! Anywhere
    I can get suitable Dawes transfers from ?

  2. Pete A said:

    Thanks for all the comments. Yes, will take bike back to LBS & get
    them to check out the front mech.........

    Quoted message said:

    Cant understand if others have upgraded bikes of this era, why this
    particular Galaxy has such a bad chainline ?

    Which way is the chainline out ? If you have the bike in middle rear, and
    middle front gear, is the front ring too far in or too far out ?

    Quoted message said:

    Does anyone know of likely costs in future if I was looking at having
    it stripped down, relevant cantilever/bottle bosses put on & resprayed
    ? The frame is basically sound, though its showing its age ! Anywhere
    I can get suitable Dawes transfers from ?

    Try one of several bike restorers, adverts often in the CTC magazine or
    other cycling magazines for quotes.
    Some will be able to provide close matches to the original Dawes transfers.

    I had my circa 1990 Nigel Dean restored by Bob Jackson last year. The
    results are superb.
    http://gallery9898.fotopic.net/c142382.html
    The bill came to around £130 including carriage of the frame up and back to
    Jackson's. The paint finish was single colour, but not the cheapest option,
    and included fitting transfers. There were also a few braise-on changes
    (chain hook, extra bottle cage bosses, revised pump peg positions).
    A friend of mine has had a Galaxy done similarly at Jackson's to a vintage
    looking design with dark green frame with white sections in the head-tube
    and seat-tube.

    If you had a more budget paint job, you may get the whole lot done for under
    £100.

    But, you would also need to factor in any extra parts you might need to
    build up the bike when painted up. Such as the new brakes, brake cables and
    anything else which you felt was sub-standard on the rebuild (cranks looking
    scuffed, chainrings a bit old, gear shifters, brake levers, etc. etc.).
    Even little things add to the cost; handlebar coverings (grab-on in my case)
    and the chainstay protector (found a carbon-like finish one from M:part
    which stays stuck on, unlike the rubberised ones which don't stick to the
    glue).

    Given the cost of some quite decent new bikes, such as Dawes from a couple
    of years ago, advertised at some dealers in magazines, you may find it more
    economical to get a new bike. Equally one can get a new frame (in more
    modern material choices) for not much more than my restoration cost.
    Therefore, unless the old bike has high sentimental value, the
    conversion/restoration may not be worthwhile.

    - Nigel

    --
    NC - Webmaster for http://www.2mm.org.uk/
    Replies to newsgroup postings to the newsgroup please.

  3. NC said:

    Therefore, unless the old bike has high sentimental value, the
    conversion/restoration may not be worthwhile.

    Thats a very good point. I have priced up getting my tourer refinished
    at Jacksons and to the standard I'd like, which is nowhere near its
    original standard would be prohibitively expensive. It has got
    sentimental value so I'll use it until it falls apart then get a new
    frame and port as many parts as I can.

Active in the last 60 minutes

Active in this thread

0 users · 0 guests ·0 bots ·0 total

No signed-in users are active right now.

No known search crawlers active right now.