Cycling Equipment · Public discussion

Tektro "mini V' brakes

Started by Chris Zacho "Th · · Last activity · 4 posts · 1,364 views

Thread details

What we know about this thread

Original section
Cycling Equipment
Published
10 April 2003
Last activity
11 April 2003
Original author
Chris Zacho "Th
Posts
4
Discussion status
Public discussion
Total views
1,364
Views / 30 days
0

The navigation and discussion metadata provide context. Posts remain in their original chronological order.

Showing posts 1–4 of 4
Posts remain in their original chronological order.

Text size
  1. In another thread "Klydsdale" posted a link showing a linear pull brake for road bikes
    chucksbikes.combkminv.htm

    I have a question about these brakes.

    I cannot put standard Linear pulls on mytouring frame. Not because of cable pull, they have levers
    and adapters for that, but because of rim clearance.

    I have an older frame, and the bosses are too close together. I therefore cannot even mount them.
    Even with narrow rims. This, in fact is what led me to the idea of my "cantilever/linear pull
    conversion".

    So my question is, does anybody here have these brakes, and is the geometry the same as standard
    full length LP's? Do they require the same amount of rim clearance, that is?

    May you have the wind at your back. And a really low gear for the hills! Chris

    Chris'Z Corner "The Website for the Common Bicyclist": geocities.comczcorner

  2. Quoted message said:

    I have an older frame, and the bosses are too close together. I therefore cannot even mount them.
    Even with narrow rims.

    You may try swapping the left/right V-brakes' arms. People did this with extra-wide rims ("Snow Cat
    rims" for winter cycling), when there was not enough clearance between bosses.

    Picture is at users.rcn.comrims.h2.jpg.

    --
    Konstantin Shemyak

    Remove the obvious 2 parts from the "reply-to"

  3. [email hidden] (Chris Zacho "The Wheelman"😉 wrote in message
    news:<[email hidden]>...

    Quoted message said:


    So my question is, does anybody here have these brakes, and is the geometry the same as standard
    full length LP's? Do they require the same amount of rim clearance, that is?

    Chris, I have a set of these... somewhere in my garage. I don't think they'll solve your problem-
    the pad-to-pivot arrangement is close to the same as "regular" V-brakes.

    I'm assuming you've tried tried playing around with the spacing washers on the brake shoes to gain
    additional space.

    Jeff

  4. I've tried REMOVING the washers. As many as I could, anyways. A couple of brands the pads attached
    like on regular canti's, so there were no washers to remove.

    Those couple of brands I could get on the rear. None would go on the front. I couldn't even get the
    wheel on with them mounted. Or vice versa.

    I considered getting new forks, but the only ones I could find with cantilever bosses were the big
    bulky ones for mountain bikes. (anybody know where I can find a nice set of lugged road forks with
    cantilever bosses (D/B'd preferred) ? )

    I've never thought of swapping the arms left/right. I might try that with the linears I'm taking off
    my MTB. But from what I've seen so far, it doesn't look hopeful.

    What I may end up doing is canabalizing my linears for a couple of parts and improve my
    cantilever-to- linear conversion. If it works, I'll put it on my site :-3)

    May you have the wind at your back. And a really low gear for the hills! Chris

    Chris'Z Corner "The Website for the Common Bicyclist": geocities.comczcorner

Active in the last 60 minutes

Active in this thread

0 users · 0 guests ·0 bots ·0 total

No signed-in users are active right now.

No known search crawlers active right now.