Shimano PD-M424 pedals

Jay Goldstein said:

I've run into a problem with the spring tension of a binding on my new Shimano PD-M424 pedals. I've
adjusted the spring tension on all four bindings to be very low (for ease of release). However,
even at the lowest setting (i.e., the red tension indicator is barely visible) the tension on one
of the bindings is still quite high (i.e., it takes a considerable effort to engage and disengage
from that binding).

I'm wondering whether the binding is defective, or can I expect the spring tension on that binding
to lessen as the pedal gets "broken in"? BTW, I've ridden about 50 km (about 30 mi) with the new
pedals and haven't noticed any change in the spring tension yet.

Jay Goldstein Winnipeg, MB, Canada

Two things to try; tighten the tension to maximum then back it out again to where you want it, in
case the spring has snagged somewhere in the internals; check for any asymmetry in the plastic cage
surrounding the pedal, in case interference between the sole and the cage is causing the feeling of
high engagement force. Which cleats are you using? The 424/434 seems to work best with the SH-55
multirelease cleats, especially in the dirt. The multirelease lets you get out even when there are
stones in your tread pattern interfering with the cages.

Kinky Cowboy Kinky Cowboy

*Your milage may vary Batteries not included May contain traces of nuts.

I had tried adjusting the tension to maximum and then back to minimum when I installed the pedals
initially. On your suggestion, I tried it again, and there was no improvement. I concluded that the
binding was defective.

I've just gotten back from Mountain Equipment Co-Op, where they cheerfully gave me a new pedal. The
tension adjustment on both bindings of the new pedal works fine. Problem solved.

BTW, my pedals came with the single release mode cleats.

Jay Goldstein Winnipeg, MB, Canada

"KinkyCowboy" <[email hidden]> wrote in message
news:72448339eae69e230d0486fc6d7e0498@TeraNews...

Quoted message said:

On 3 May 2003 15:45:01 GMT, Jay Goldstein <[email hidden]> wrote:

Two things to try; tighten the tension to maximum then back it out again to where you want it, in
case the spring has snagged somewhere in the internals; check for any asymmetry in the plastic
cage surrounding the pedal, in case interference between the sole and the cage is causing the
feeling of high engagement force. Which cleats are you using? The 424/434 seems to work best with
the SH-55 multirelease cleats, especially in the dirt. The multirelease lets you get out even when
there are stones in your tread pattern interfering with the cages.

Kinky Cowboy Kinky Cowboy

*Your milage may vary Batteries not included May contain traces of nuts.

"Jay Goldstein" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

I've run into a problem with the spring tension of a binding on my new Shimano PD-M424 pedals.
I've adjusted the spring tension on all four bindings to be very low (for ease of release).
However, even at the lowest setting (i.e., the red tension indicator is barely visible) the
tension on one of the bindings is still quite high (i.e., it takes a considerable effort to engage
and disengage from that binding).

I'm wondering whether the binding is defective, or can I expect the spring tension on that binding
to lessen as the pedal gets "broken in"? BTW, I've ridden about 50 km (about 30 mi) with the new
pedals and haven't noticed any change in the spring tension yet.

SPD pedal binding mechanisms seem to "wear-in" and get easier to get in/out of, but it can take a
while. I lubricate mine when they are new, where there is metal-to-metal contact between the cleat
and pedal.

--
rec.bicycles.off-road is moderated by volunteers. To find help solving posting problems, or contact
the moderators, please see rbor.orgrbor.orgOpen ↗ Please read the charter before posting:
rbor.orgrbor charter.txtOpen ↗

Jay Goldstein said:

I've run into a problem with the spring tension of a binding on my new Shimano PD-M424 pedals.
I've adjusted the spring tension on all four bindings to be very low (for ease of release).
However, even at the lowest setting (i.e., the red tension indicator is barely visible) the
tension on one of the bindings is still quite high (i.e., it takes a considerable effort to engage
and disengage from that binding).

I'm wondering whether the binding is defective, or can I expect the spring tension on that binding
to lessen as the pedal gets "broken in"? BTW, I've ridden about 50 km (about 30 mi) with the new
pedals and haven't noticed any change in the spring tension yet.

Jay Goldstein Winnipeg, MB, Canada

They wear-in, but VERY slowly (k's of miles). I've found it to be not unusual to have some
difference, but not much. I would try reducing that one alone to see if I could balance them
(someone may have been playing with them in the shop and left them set wrong). If it still seems
wrong after you've played with it a bit, I'd take it back to where I bought it and get a new set.

David

--
rec.bicycles.off-road is moderated by volunteers. To find help solving posting problems, or contact
the moderators, please see rbor.orgrbor.orgOpen ↗ Please read the charter before posting:
rbor.orgrbor charter.txtOpen ↗